Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1038 (FRONT SUSPENSION SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2
Fastener Tightening Specifications
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Brake Hose Bracket Bolt | 9 N.m | 80 lb in |
| Brake Hose Clip Bolts | 12 N.m | 106 lb in |
| ESC Sensor Bracket Bolt | 25 N.m | 18 lb ft |
| Hub and Bearing Assembly to Steering Knuckle Bolts | 180 N.m | 133 lb ft |
| Lower Ball Joint Stud Nut | 110 N.m | 81 lb ft |
| Lower Control Arm to Frame Nuts | 175 N.m | 129 lb ft |
| Shock Absorber Module to Frame Nuts | 50 N.m | 37 lb ft |
| Shock Absorber Module to Lower Control Arm Bolt | 50 N.m | 37 lb ft |
| Shock Absorber Tenon Nut - 1500 Series | 50 N.m | 37 lb ft |
| Shock Absorber Tenon Nut - 2500 Series | 24 N.m | 17 lb ft |
| Shock Absorber to Lower Control Arm Bolts - 2500 Series | 25 N.m | 18 lb ft |
| Stabilizer Shaft Insulator Clamp Bolts | 50 N.m | 37 lb ft |
| Stabilizer Shaft Link Nuts - 1500 Series | 23 N.m | 17 lb ft |
| Stabilizer Shaft Link Nuts - 2500 Series | 14 N.m | 124 lb in |
| Suspension Position Sensor Bolt | 12 N.m | 106 lb in |
| Upper Ball Joint Stud Nut | 50 N.m | 37 lb ft |
| Upper Control Arm to Frame Nuts | 190 N.m | 140 lb ft |
| Wheel Drive Shaft to Front Hub Nut | 240 N.m | 177 lb ft |
| Wheel Speed Sensor Mounting Bolt | 18 N.m | 13 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.