Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSISBODY & FRAMEDOOR LOCKSTHEFT DETERRENT SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2
Scan Tool Data List
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Scan Tool Data List
Body Control Module (BCM)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Ignition ON/Engine OFF/Vehicle in PARK/Headlamps in AUTO | |||
| Auto Learn Timer | Security Data | Seconds | 0-600 |
| Battery Voltage | Security Data | Volts | Varies |
| Content Theft Lamp | Security Data | ON/OFF | OFF |
| Content Theft State | Security Data | ON/OFF | OFF |
| Door Handle Switch | Input 1 | ACTIVE/INACTIVE | ACTIVE (door open) |
| Door Key Switch | Security Data | ACTIVE/INACTIVE | ACTIVE |
| Driver Door Jamb Switch | Input 1 | ACTIVE/INACTIVE | ACTIVE (door open) |
| Ignition 1 | Security Data | ACTIVE/INACTIVE | ACTIVE |
| Ignition 3 | Security Data | ACTIVE/INACTIVE | ACTIVE |
| Manufacture Enable Counter | Module Information 1 | 0-255 | 0 |
| Module Part Number | Module Information 1 | Numeric | Varies |
| Passlock Code | Security Data | Open/Short/Tamper/Numeric | Valid Code 1-10 |
| Passlock Data Voltage | Security Data | Volts | 0.86-5 Volts |
| Passlock State | Security Data | Ignition Off/Tamper/Fail Enable/Fail Enable Dec/Seedkey Lrn Pend/Seedkey Learn/Auto Learn Pend/Learn Passlock/Monitor Passlock/Normal Decision/Auto Learn | Monitor Passlock |
| Security Calibration Number | Module Information 2 | Numeric | Varies |
| Security Lamp State | Security Data | ON/OFF/FLASHING | OFF |
| Security Suffix | Module Information 2 | Two Letters | Varies |
| Tamper Timer | Security Data | Seconds | 0-600 |
| VCM/PCM Fail Enable | Security Data | YES/NO | NO |
| VCM/PCM Fuel Continue | Security Data | YES/NO | YES |
| VCM/PCM Learn Timer | Security Data | ACTIVE/INACTIVE | INACTIVE |
| VTD Fuel Disable | Security Data | ACTIVE/INACTIVE | INACTIVE |
| VTD Fuel Disable Until Ignition Off | Security Data | YES/NO | NO |
| VTD Password Learn Mode | Security Data | ACTIVE/INACTIVE | INACTIVE |
Powertrain Control Module (PCM)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Ignition ON/Engine OFF/Vehicle in PARK/Headlamps in AUTO | |||
| PCM/VCM in VTD Fail Enable | Engine Data 1 | Yes/No | No |
| VTD Auto Learn Timer | Engine Data 1 | Active/Inactive | Inactive |
| VTD Fuel Disable | Engine Data 1 | Active/Inactive | Inactive |
| VTD Fuel Disable Until Ign. OFF | Engine Data 1 | Yes/No | No |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.