Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO, 6.6 2REPAIR AND DIAGNOSIS (SINGLE PAGE)BODY & FRAMEDOOR LOCKSTHEFT DETERRENT SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESDTC P1626TEST DESCRIPTION
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2
Test Description
2006 Chevrolet Chevy Express G2500, Van Cargo, 6.6 2SECTION Test Description
The numbers below refer to the step numbers on the diagnostic table.
- 2: This test checks if communications can be established between the scan tool and the BCM.
- 3: This test checks for any opens in the serial data circuit between the PCM and the BCM. This also checks for any intermittent malfunctions associated with the serial data circuit.
- 4: This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the PCM is disabling fuel.
- 7: Use a scan tool to clear and check for any DTCs in all the modules connected to the class 2 serial data circuit, such as the PCM, BCM, and automatic temperature control (ATC).
DTC P1626
| Step | Action | Yes | No |
|---|---|---|---|
| Schematic Reference: Data Link Connector (DLC) Schematics in Computer/Integrating Systems | |||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
| 2 |
IMPORTANT:
You must diagnose the Bxxxx codes prior to diagnosing any Pxxxx code.
IMPORTANT:
Do not start the vehicle.
|
Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
| 3 | Check the class 2 serial data circuit for the following intermittent conditions:
Did you find a problem? |
Go to Step 6 | Go to Step 4 |
| 4 |
|
Go to Step 8 | Go to Step 5 |
| 5 | This DTC is intermittent. Are any additional DTCs stored? |
Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
| 6 | Repair the circuit as necessary. Refer to Wiring Repairs
or Connector Repairs
in Wiring Systems. Is the action complete? |
Go to Step 7 | - |
| 7 |
IMPORTANT:
Before clearing DTCs, monitor all DTC status parameters and note any additional DTCs.
|
Go to Step 2 | System OK |
| 8 | Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
Go to Step 7 | Go to Step 9 |
| 9 | Replace the BCM. Refer to Control Module References
in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? |
Go to Step 7 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.