Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO EXTENDED, 5.3 T, 4L60E/M30REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2010 (PROGRAMMING AND SETUP - ALL SYSTEMS)
2006 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.3 T, 4L60E/M30
Section 2010 (Programming And Setup - All Systems)
2006 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.3 T, 4L60E/M30SECTION Section 2010 (Programming And Setup - All Systems)
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Information and Procedures
- Repair Instructions
- Accessory AC and DC Power Control Module Programming and Setup
- Accessory DC Power Control Module Programming and Setup
- Air Conditioning Compressor Control Module Programming and Setup
- Assist Step Control Module Programming and Setup
- Audio Amplifier Programming and Setup
- Auxiliary Body Control Module Programming and Setup
- Auxiliary Heating, Ventilation, and Air Conditioning Control Module Programming and Setup
- Blower Motor Control Module Programming and Setup (Primary HVAC)
- Blower Motor Control Module Programming and Setup (Auxiliary HVAC)
- Body Control Module Programming and Setup
- Communication Interface Module Programming and Setup
- Control Solenoid Valve and Transmission Control Module Assembly Programming and Setup (2ML70)
- Control Solenoid Valve and Transmission Control Module Assembly Programming and Setup (6L45/6L50/6L80/6L90)
- Digital Radio Receiver Programming and Setup
- Door Lock and Side Window Switch Programming and Setup
- Drive Motor Generator Battery Control Module Programming and Setup
- Drive Motor Generator Power Inverter Module Programming and Setup
- Electronic Brake Control Module Programming and Setup
- Electronic Compass Module Programming and Setup
- Electronic Suspension Control Module Programming and Setup
- Engine Control Module Programming and Setup
- Fuel Pump Flow Control Module Programming and Setup
- Garage Door Opener Programming and Setup
- Headlamp Control Module Programming and Setup
- Heated Seat Control Module Programming and Setup
- HVAC System Control Module Programming and Setup
- Inflatable Restraint Sensing and Diagnostic Module Programming and Setup
- Inside Rearview Mirror Programming and Setup
- Instrument Cluster Programming and Setup
- Liftgate Control Module Programming and Setup
- Memory Seat Control Module Programming and Setup
- Object Alarm Module Programming and Setup
- Passenger Presence System Programming and Setup
- Power Steering Control Module Programming and Setup
- Radio Programming and Setup
- Rear Seat Heater Control Module Programming and Setup
- Remote Control Door Lock Receiver Programming and Setup
- Seat Climate Control Module Programming and Setup
- Serial Data Gateway Module Programming and Setup
- Service Programming System (SPS)
- Sunroof Control Module Programming and Setup
- Theft Deterrent Module Programming and Setup
- Trailer Brake Control Module Programming and Setup
- Transfer Case Shift Control Module Programming and Setup (MP 3010-NP0)
- Transfer Case Shift Control Module Programming and Setup (MP 3023/3024-NQH)
- Transmission Auxiliary Fluid Pump Control Module Programming and Setup
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.