Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006CHEVY EXPRESS G2500, VAN CARGO EXTENDED, 5.3 T, 4L60E/M30REPAIR AND DIAGNOSISBRAKESANTILOCK BRAKE SYSTEM WITH TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM
2006 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.3 T, 4L60E/M30
Antilock Brake System With Traction Control System & Stability Control System
2006 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.3 T, 4L60E/M30SECTION Antilock Brake System With Traction Control System & Stability Control System
- Specifications
- Schematic and Routing Diagrams
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Code Index
- Diagnostic Starting Point - Anti-Lock Brake System
- Scan Tool Output Controls (W/JL4)
- Scan Tool Output Controls (W/O JL4)
- Scan Tool Data List
- Scan Tool Data Definitions
- DTC C0035 or C0040
- DTC C0045 or C0050
- DTC C0055 or P0609
- DTC C0110
- DTC C0131
- DTC C0161 (W/O JL4)
- DTC C0161 (W/JL4)
- DTC C0186
- DTC C0196
- DTC C0201
- DTC C0220-C0229 (W/O JL4)
- DTC C0220-C0229 (W/ JL4)
- DTC C0244 or P1689
- DTC C0245
- DTC C0279
- DTC C0283
- DTC C0290 or C0292
- DTC C0455
- DTC C0550
- DTC C0558
- Symptoms - Anti-Lock Brake System
- ABS Indicator Always On
- ABS Indicator Inoperative
- Stability System Caution Indicator Always On
- Stability System Caution Indicator Inoperative
- Stability System Not Ready Indicator Always On
- Stability System Not Ready Indicator Inoperative
- Vehicle Stability Enhancement System Poor Performance
- Brake Pressure Modulator Valve Hydraulic Testing
- Repair Instructions
- ABS Automated Bleed Procedure (W/JL4)
- ABS Automated Bleed Procedure (w/o JL4)
- Electronic Brake Control Module Replacement (w/JL4)
- Electronic Brake Control Module Replacement (w/o JL4)
- Brake Pressure Modulator Valve (BPMV) Replacement (w/JL4)
- Brake Pressure Modulator Valve (BPMV) Replacement (w/o JL4)
- Brake Pressure Modulator Valve Pre-Charge Pump Replacement
- Wheel Speed Sensor Replacement (2WD)
- Wheel Speed Sensor Replacement (4WD)
- Wheel Speed Sensor Replacement - Rear
- Traction Control Switch Replacement
- Yaw Rate Reference Table Reset Procedure
- Yaw Rate Sensor/Lateral Accelerometer Replacement
- Description and Operation
- ABS Description and Operation (W/JL4)
- ABS Description and Operation (W/O JL4)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.