Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2005AVEO L4-1.6L VIN 6REPAIR AND DIAGNOSISTESTING AND INSPECTIONPROGRAMMING AND RELEARNINGREMOTE KEYLESS ENTRY (RKE) - TRANSMITTER - TECH 2 METHOD
2005 Chevrolet Aveo L4-1.6L VIN 6
Remote Keyless Entry (RKE) - Transmitter - Tech 2 Method
2005 Chevrolet Aveo L4-1.6L VIN 6SECTION Remote Keyless Entry (RKE) - Transmitter - Tech 2 Method
TRANSMITTER PROGRAMMING (TECH 2)
IMPORTANT: All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to five transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
Transmitter Programming Procedure
IMPORTANT: Turn the ignition to ON before installing in the scan tool. Failure to connect in this procedure may cause communication errors and the programming procedure will not complete. Any keys that are not programmed at this time will no longer function.
1. Turn ON the ignition with the engine OFF.
2. Install the scan tool.
3. Select PROGRAMMING KEY FOBS from the BODY menu.
4. Follow the scan tool instructions with each key until all keys are programmed.
5. Turn the ignition to the LOCK position, disconnect the TECH 2 and test all the keys.
6. If any key does not function, refer to Keyless Entry Does Not Program.
For immobilizer programming, refer to Programming Additional Keys in Theft Deterrent System.
IMPORTANT: All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to five transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
Transmitter Programming Procedure
IMPORTANT: Turn the ignition to ON before installing in the scan tool. Failure to connect in this procedure may cause communication errors and the programming procedure will not complete. Any keys that are not programmed at this time will no longer function.
1. Turn ON the ignition with the engine OFF.
2. Install the scan tool.
3. Select PROGRAMMING KEY FOBS from the BODY menu.
4. Follow the scan tool instructions with each key until all keys are programmed.
5. Turn the ignition to the LOCK position, disconnect the TECH 2 and test all the keys.
6. If any key does not function, refer to Keyless Entry Does Not Program.
For immobilizer programming, refer to Programming Additional Keys in Theft Deterrent System.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.