Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Test Description
2003 Chevrolet TrailBlazer 4.2 S, 4WDSECTION Test Description
WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
The numbers below refer to the step numbers on the diagnostic table.
- 2: Listen for an audible click when the DRL relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
- 3: Tests for voltage at the coil side of the DRL relay.
- 4: Verifies that the body control module is providing ground to the DRL relay.
- 5: Tests if ground is constantly being applied to the DRL relay.
DTC B2602
| Step | Action | Yes | No |
|---|---|---|---|
| Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics | |||
| 1 | Did you perform the Lighting System Diagnostic System Check? | Go to Step 2 | Go to Diagnostic System Check - Lighting Systems |
| 2 |
|
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
| 3 |
|
Go to Step 4 | Go to Step 10 |
| 4 |
|
Go to Step 8 | Go to Step 5 |
| 5 | Does the test lamp remain illuminated with each command? | Go to Step 7 | Go to Step 6 |
| 6 | Test the control circuit of the DRL relay for an open. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
Go to Step 13 | Go to Step 9 |
| 7 | Test the control circuit of the DRL relay for a short to ground. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
Go to Step 13 | Go to Step 9 |
| 8 | Inspect for poor connections at the DRL relay. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
Go to Step 13 | Go to Step 11 |
| 9 | Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
Go to Step 13 | Go to Step 12 |
| 10 | Repair an open, high resistance, or short to ground in the coil side battery positive voltage circuit of the DRL relay. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you complete the repair? |
Go to Step 13 | - |
| 11 | Replace the DRL relay. Did you complete the replacement? |
Go to Step 13 | - |
| 12 |
IMPORTANT:
Perform the set up procedure for the body control module. Replace the body control module. Refer to Body Control Module Replacement
in Body Control System.Did you complete the replacement? |
Go to Step 13 | - |
| 13 |
|
Go to Step 2 | System OK |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.