Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2003TRAILBLAZER 4.2 S, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1554 (POWER STEERING SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2003 Chevrolet TrailBlazer 4.2 S, 4WD
Fastener Tightening Specifications
2003 Chevrolet TrailBlazer 4.2 S, 4WDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2003 GMC Sierra, 2003 GMC Cab & Chassis Sierra, 2003 Chevrolet Silverado, and 2003 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Accessory Mounting Bracket Bolts | 50 N.m | 37 lb ft |
| Accessory Mounting Bracket Nuts | 41 N.m | 30 lb ft |
| Adjuster Lock Nut | 49 N.m | 36 lb ft |
| Bali Guide Screws | 6 N.m | 53 lb in |
| Battery Junction Block Retaining Bolt | 9 N.m | 80 lb in |
| Connector Fitting Assembly | 75 N.m | 55 lb ft |
| Coupling Shield and Lock Nut | 108 N.m | 80 lb ft |
| Cylinder End Fitting | 27 N.m | 20 lb ft |
| Filler Neck Retaining Nut | 25 N.m | 18 lb ft |
| Front Pump Mounting Bolts | 50 N.m | 37 lb ft |
| Gear To Frame Bolts (Non-Rack and Pinion) | 150 N.m | 110 lb ft |
| Gear To Frame Bolts (Rack and Pinion) | 185 N.m | 136 lb ft |
| Inner Tie Rod to Steering Gear | 100 N.m | 74 lb ft |
| Intermediate Shaft Coupling Pinch Bolt | 45 N.m | 33 lb ft |
| Oil Pan Skid Plate Bolts | 20 N.m | 15 lb ft |
| Outer Tie Rod to the Steering Knuckle | 50 N.m | 37 lb ft |
| Pitman Arm to Gear Nut | 250 N.m | 184 lb ft |
| Pitman Arm to Relay Rod Nut | 62 N.m | 46 lb ft |
| Pitman Shaft Cover Bolts | 62 N.m | 46 lb ft |
| Power Steering Cooler Mounting Bolts | 5 N.m | 44 lb in |
| Power steering Mounting Bolts (6.6L Diesel) | 46 N.m | 34 lb ft |
| Power Steering Pump Mounting Studs | 58 N.m | 43 lb ft |
| Pressure Hose Connection (At Gear) | 28 N.m | 20 lb ft |
| Pressure Hose Connection (At Pump) | 28 N.m | 20 lb ft |
| Rack and Pinion Ground Strap Retaining Bolt | 10 N.m | 89 lb in |
| Rack and Pinion Adjuster Lock Nut | 68 N.m | 50 lb ft |
| Rack and Pinion Cylinder Fittings | 28 N.m | 20 lb ft |
| Rack and Pinion Hex Lock Nut | 30 N.m | 22 lb ft |
| Rack and Pinion Piston Plug | 150 N.m | 111 lb ft |
| Rear Pump Mounting Bolt | 50 N.m | 37 lb ft |
| Side Cover Bolts | 60 N.m | 45 lb ft |
| Stub Shaft Housing Bolts | 55 N.m | 45 lb ft |
| Thrust Bearing Adjuster Nut | 31 N.m | 23 lb ft |
| Tie Rod Jam Nut | 68 N.m | 50 lb ft |
| Valve End Fitting | 17 N.m | 13 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.