SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2003TRAILBLAZER 4.2 S, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1506 (BUMPER SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2003 Chevrolet TrailBlazer 4.2 S, 4WD

Fastener Tightening Specifications

2003 Chevrolet TrailBlazer 4.2 S, 4WDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications

Application Specification
Metric English
Antenna Ground Nut 6 N.m 53 lb in
Antenna Ground Stud 5 N.m 44 lb in
Air Deflector Bolts 3 N.m 27 lb in
Air Deflector Bolts 7 N.m 62 lb in
Backup Lamp/Rear License Bracket Screws 1 N.m 9 lb in
Brake Caliper Cooling Air Scoop Nuts 3 N.m 27 lb in
Brake Caliper Cooling Duct Bolt 2 N.m 18 lb in
Fascia Grille Screws 2 N.m 18 lb in
Fascia Lamp Deflector Bolts 3 N.m 27 lb in
Front Energy Absorber Bolts 5 N.m 44 lb in
Front Fascia Bracket Bolts 7 N.m 62 lb in
Front Fascia Lower Close Out Panel Bolts 7 N.m 62 lb in
Front Fascia Lower Flange to Radiator Support Screws 8 N.m 71 lb in
Front Fascia Retainer Bolts 7 N.m 62 lb in
Front Fascia to Fender Reinforcement Bolts 5 N.m 44 lb in
Front Fascia to Fender Reinforcement Stud Nut 5 N.m 44 lb in
Front Fascia to Skid Bar Bolt 3 N.m 27 lb in
Front Fascia Upper Flange Bolts 5 N.m 44 lb in
Front License Bracket Bolts 1 N.m 9 lb in
Front Wheelhouse to Fascia Bolts 3 N.m 27 lb in
License Bracket Screws 2 N.m 18 lb in
License Plate Opening to Absorber Screws 1 N.m 9 lb in
Outer Valance Bolts 7 N.m 62 lb in
Rear Energy Absorber Attaching Bolts 5 N.m 44 lb in
Rear Fascia Retainer Bracket Stud Nuts 10 N.m 89 lb in
Rear Fascia to Quarter Panel Reinforcement Screws 5 N.m 44 lb in
Rear Fascia to Rear Compartment Brace Bolts 5 N.m 44 lb in
Rear Fascia Upper Flange Screws 2 N.m 18 lb in
Rear License Plate Opening to Energy Absorber Screws 1 N.m 9 lb in
Reflector Nuts 2 N.m 18 lb in
Tail Lamp Screws 2 N.m 18 lb in
Valance Screws 7 N.m 62 lb in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.