Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2003TRAILBLAZER 4.2 S, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 143 (ENGINE CONTROLS - SYSTEM & COMPONENT TESTING)FUEL SYSTEM (DIESEL)GLOW PLUG SYSTEM DIAGNOSIS (6.6L)DIAGNOSTIC PROCEDURE
2003 Chevrolet TrailBlazer 4.2 S, 4WD
Diagnostic Procedure
2003 Chevrolet TrailBlazer 4.2 S, 4WDSECTION Diagnostic Procedure
WARNING: This page does not describe the selected car, but rather 31 other vehicles, including the 2002 Saturn Vue, 2002 Pontiac Montana, 2002 Pontiac Aztek, 2002 Oldsmobile Silhouette, and 2002 Oldsmobile Bravada. However, it is still accessible from the selected car via links, so may be relevant.
- Perform Diagnostic System Check - Engine Controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS under SELF-DIAGNOSTIC SYSTEM in SELF-DIAGNOSTICS - 6.6L SIERRA & SILVERADO article. After performing Diagnostic System Check - Engine Controls, go to next step.
- Retrieve DTCs. If DTC P0117, P0118 and/or P0380 is not set, go to next step. If DTC P0117, P0118 and/or P0380 is set, perform appropriate DTC test. See DIAGNOSTIC TROUBLE CODE DEFINITIONS in SELF-DIAGNOSTICS - 6.6L SIERRA & SILVERADO article.
- Turn ignition off. Disconnect all glow plug harness connectors. Using a test light connected to battery voltage, probe each glow plug spade terminal at glow plugs. If test light illuminates at each glow plug, go to next step. If test light does not illuminate at each glow plug, go to step 9.
- Ensure all glow plug harness connectors are still disconnected. Turn ignition on with engine off. Using scan tool, command glow plugs on. Using a test light connected to ground, probe each glow plug harness connector terminal. If test light illuminates at each glow plug harness connector, go to next step. If test light does not illuminate at each glow plug harness connector, go to step 10.
- Using scan tool, command glow plugs off. Using a test light connected to ground, probe each glow plug harness connector terminal. If test light illuminates at any glow plug harness connector, go to next step. If test light does not illuminate at any glow plug harness connector, go to step 11.
- Remove glow plug relay. Using a test light connected to ground, probe each glow plug harness connector terminal. If test light illuminates at any glow plug harness connector, go to next step. If test light does not illuminate at any glow plug harness connector, go to step 8.
- Repair short to voltage in Glow Plug Output circuit or Glow Plug Signal circuit. After repairs, go to step 11.
- Replace glow plug relay. After repairs, go to step 11.
- Replace glow plugs that did not illuminate test light. After repairs, go to step 11.
- Repair open in glow plug circuit(s) that did not illuminate test light. After repairs, go to next step.
- Operate vehicle under conditions when problem was noted. If system does not operate properly, go to step 1.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.