Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSCHEVROLET2002AVALANCHE 2500, RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 898 (AUTOMATIC TRANSMISSION - 4L80-E/4L85-E (INTRODUCTION, SERVICE & REPLACEMENT))COMPONENT LOCATORAUTOMATIC TRANSMISSION RELATED CONNECTORS
2002 Chevrolet Avalanche 2500, RWD
Automatic Transmission Related Connectors
2002 Chevrolet Avalanche 2500, RWDSECTION Automatic Transmission Related Connectors
WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Automatic Transmission Input Shaft Speed (AT ISS) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | RED/BLK | 1230 | Transmission Input Speed Sensor Signal High |
| B | DK BLU/WHT | 1231 | Transmission Input Speed Sensor Signal Low |
Automatic Transmission Output Shaft Speed (AT OSS) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PPL/WHT | 821 | Transmission Output Speed Sensor Signal High |
| B | LT GRN/BLK | 822 | Transmission Output Speed Sensor Signal Low |
Transmission Range Switch, Wiring Harness Side
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | DK GRN | 1433 | Clutch Start Switch Signal |
| 2-3 | - | - | Not Used |
| 4 | YEL | 772 | Transmission Range Switch Signal B |
| 5 | BLK/WHT | 771 | Transmission Range Switch Signal A |
| 6 | GRY | 773 | Transmission Range Switch Signal C |
| 7 | BLK/WHT | 451 | Ground |
| 8 | WHT | 776 | Transmission Range Switch Signal P |
| 9 | LT GRN | 275 | Park Neutral Position Switch Signal |
| 10 | GRY | 1524 | Back-Up Lamp Supply Voltage |
| 11 | PNK | 839 | Ignition 1 Voltage |
| 12 | PPL | 639 | Ignition 1 Voltage |
Tow/Haul Switch, Column Wiring Harness Side
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT BLU | 553 | Tow/Haul Switch Input |
| B | BLK | 1850 | Tow/Haul Switch Ground |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.