Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001S10 PICKUP 2D PICKUP, 2.2 5, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 754 (HEATING, VENTILATION AND AIR CONDITIONING)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2001 Chevrolet S10 Pickup 2D Pickup, 2.2 5, Automatic
Fastener Tightening Specifications
2001 Chevrolet S10 Pickup 2D Pickup, 2.2 5, AutomaticSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| A/C Refrigerant Filter Flare Nut | 15 N.m | 11 lb ft |
| Accumulator Bracket Clamp Bolt | 10 N.m | 89 lb in |
| Accumulator Bracket Mounting Nuts | 10 N.m | 89 lb in |
| Accumulator Hose Fitting to Accumulator | 41 N.m | 30 lb ft |
| Accumulator Hose to Evaporator Retaining Bolt | 16 N.m | 12 lb ft |
| Blower Motor Resistor Retaining Screws | 1.6 N.m | 14 lb in |
| Blower Motor Retaining Screws | 1.7 N.m | 15 lb in |
| Compressor Drain Plug | 20 N.m | 15 lb ft |
| Compressor Drive Belt Idler Pulley Bolt | 50 N.m | 37 lb ft |
| Compressor Drive Belt Tensioner Bolt | 25 N.m | 18 lb ft |
| Compressor Hose to Accumulator Retaining Bolt | 20 N.m | 15 lb ft |
| Compressor Hose to Compressor Retaining Bolt | 26 N.m | 19 lb ft |
| Compressor Hose to Condenser Fitting Nut | 24 N.m | 17 lb ft |
| Compressor Mounting Bolts | 40 N.m | 30 lb ft |
| Compressor Mounting Bracket Bolt | 50 N.m | 37 lb ft |
| Compressor Mounting Nut | 40 N.m | 30 lb ft |
| Compressor Mounting Stud | 9 N.m | 80 lb in |
| Compressor Pressure Relief Valve | 9 N.m | 80 lb in |
| Compressor Shaft Nut | 17.5 N.m | 13 lb ft |
| Defroster Duct Retaining Screws | 10 N.m | 89 lb in |
| Floor Air Outlet Duct Retaining Screws | 1.6 N.m | 14 lb in |
| Front Evaporator Tube to Condenser Retaining Bolt | 27 N.m | 20 lb ft |
| Front Evaporator Tube to Rear Evaporator Tube Retaining Bolt | 25 N.m | 18 lb ft |
| Heater Core Cover Retaining Screws | 1.6 N.m | 14 lb in |
| Heater Core Outlet Cover Retaining Screws | 1.6 N.m | 14 lb in |
| Heater Core Pipe Retainer Clamp Screw | 1.6 N.m | 14 lb in |
| Heater Core Retaining Clamp Screw | 1.6 N.m | 14 lb in |
| Heater Pipe Assembly Retaining Bolt | 16 N.m | 12 lb ft |
| Heater Pipe Bracket Retaining Nut | 10 N.m | 89 lb in |
| HVAC Module Case Half Screws | 1.6 N.m | 14 lb in |
| HVAC Module Retaining and Sealing Nuts | 10 N.m | 89 lb in |
| HVAC Module Retaining Bolts | 10 N.m | 89 lb in |
| Ignition Switch Retaining Bolts | 5.5 N.m | 49 lb in |
| IPC to Steering Column Bracket Retaining Screws | 3.5 N.m | 31 lb in |
| Negative Battery Cable Bolt | 15 N.m | 11 lb ft |
| Refrigerant Pressure Sensor | 4.75 N.m | 42 lb in |
| Temperature Actuator Retaining Screws | 1.5 N.m | 13 lb in |
| Vacuum Tank Retaining Screws | 3.5 N.m | 31 lb in |
| Valve Core | 11 N.m | 97 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.