Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001CHEVY EXPRESS G3500, VAN PASSENGER EXTENDED, 6.5 FREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 3 (ENGINE CONTROLS - SELF-DIAGNOSTICS - 8.1L)INSPECTION/MAINTENANCE PROCEDURESINSPECTION/MAINTENANCE HEATED OXYGEN SENSOR SYSTEM SET PROCEDUREDIAGNOSTIC PROCEDURES
2001 Chevrolet Chevy Express G3500, Van Passenger Extended, 6.5 F
Diagnostic Procedures
2001 Chevrolet Chevy Express G3500, Van Passenger Extended, 6.5 FSECTION Diagnostic Procedures
WARNING: This page is about a different variant/trim than selected.
- Perform inspection/maintenance system check. See INSPECTION/MAINTENANCE SYSTEM CHECK . After performing inspection/maintenance system check, go to next step.
- Ensure vehicle meets the specific conditions under CONDITIONS FOR RUNNING . Turn off all accessories (e.g., A/C, blower fan, etc.). Start engine and allow to idle for 2 minutes. Accelerate vehicle at part throttle to 45-55 MPH and maintain speed for 6 minutes or until I/M system status updates to YES. Vehicles equipped with either a 5-speed or 6-speed M/T may require operation in 4th or 5th gear respectively, in order for this test to run. Using scan tool, observe I/M SYSTEM STATUS display. If HO2S/O2S system status updates to YES, go to step 5. If HO2S/O2S system status does not update to YES, go to next step.
- Using a scan tool, observe the DTC INFO. If scan tool indicates any failed DTCs, diagnose affected DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . If scan tool does not indicate any failed DTCs, go to next step.
- Using scan tool, observe the NOT RAN SINCE CODE CLEARED display to determine if DTCs P0133 or P0153, P0140 or P0160, P1133 or P1153, P1134 or P1154 have run. Determine which of the DTCs required for a YES status have not been run. Enter DTC in SPECIFIC DTC menu on scan tool. Operate vehicle within conditions under CODE ENABLE CRITERIA for the specific DTC to run. Repeat procedure until scan tool indicates the diagnostic test has run. Repeat this step for any additional required DTCs that have not run. Using scan tool, observe I/M SYSTEM STATUS display. If status updates to YES, go next step. If status does not update to YES, see DIAGNOSTIC AIDS .
- Using scan tool, observe the emission related DTC portion of the I/M System Status display. If scan tool indicates any emission related DTCs set, diagnose affected DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . If scan tool does not indicate any emission related DTCs set, system is okay.
WARNING:
Road test vehicle under safe conditions and while obeying all traffic laws. Do not attempt any maneuvers that could jeopardize vehicle control. Failure to adhere to these precautions could lead to serious personal injury and vehicle damage.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.