SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001CHEVY EXPRESS G2500, VAN CARGO EXTENDED, 5.7 R, L31/KL8REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 349 (BODY REAR END)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2001 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.7 R, L31/KL8

Fastener Tightening Specifications

2001 Chevrolet Chevy Express G2500, Van Cargo Extended, 5.7 R, L31/KL8SECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2002 GMC Savana Special, 2002 GMC Savana Camper Special, 2002 GMC Savana, and 2002 Chevrolet Chevy Express. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications

Application Specification
Metric English
Center High Mounted Stop Lamp Applique to Body Nuts 6 N.m 53 lb in
Center High Mounted Stop Lamp Applique to Body Screws 2 N.m 18 lb in
Fuel Filler Door to Body Screws 5 N.m 44 lb in
Jack Stowage Bracket Bolts 8 N.m 71 lb in
Jack Stowage Bracket to Vehicle Nuts 10 N.m 89 lb in
Jack and Tool Container Retainer Nut 5 N.m 44 lb in
Jack and Tool Container Stowage Tray to Floor Nuts 28 N.m 21 lb ft
Left Rear Door Hinge to Body Retaining Bolts 25 N.m 18 lb ft
Left Rear Door Latch Handle Retaining Nuts 11 N.m 97 lb in
Left Rear Door Lock Striker 24 N.m 18 lb ft
Left Rear Door Lower Latch Bolts 25 N.m 18 lb ft
Left Rear Door Upper Latch Bolts 25 N.m 18 lb ft
Outside Door Handle and License Pocket Assembly Retaining Nuts 11 N.m 97 lb in
Rear Door Extension Panel Bolts 2 N.m 18 lb in
Rear Door Lower Striker Bolts 10 N.m 89 lb in
Rear Door Trim Plate Retaining Screw 2 N.m 18 lb in
Rear Door Upper Striker Bolts 10 N.m 89 lb in
Rear Door Wedge Bolts 10 N.m 89 lb in
Right Rear Door Hinge to Body Retaining Bolts 25 N.m 18 lb ft
Upper Quarter Panel Applique to Body Nuts 6 N.m 53 lb in
Upper Quarter Panel Applique to Body Screws 3 N.m 27 lb in
Window Hinge to Door Screws 3 N.m 27 lb in
Window Latch to Door 3 N.m 27 lb in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.