Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001CAVALIER LS, 2.4 TREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 86 (ENGINE CONTROLS SELF-DIAGNOSTICS)DIAGNOSTIC TESTSDTC P0116: ECT SENSOR PERFORMANCEDIAGNOSTIC PROCEDURES
2001 Chevrolet Cavalier LS, 2.4 T
Diagnostic Procedures
2001 Chevrolet Cavalier LS, 2.4 TSECTION Diagnostic Procedures
WARNING: This page is about a different car, the 2003 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
- Did you perform the Diagnostic System Check-Engine Controls? If yes, go to next step. If no, see DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS under SELF-DIAGNOSTIC SYSTEM.
- Is the cooling system low on coolant? If yes, repair and refill cooling system. If no, go to next step.
- Turn ignition OFF. Disconnect ECT sensor. Connect a 3-amp fused jumper wire between the ECT sensor signal circuit and the ECT sensor low reference circuit. Turn ignition ON, with engine OFF. Observe ECT sensor temperature with a scan tool. Does the scan tool indicate that ECT sensor temperature is greater than 280°F (138°C)? If yes, go to next step. If no, go to step 5.
- Turn ignition OFF. Disconnect IAT sensor. Connect a 3-amp fused jumper wire between the IAT sensor signal circuit and the IAT sensor low reference circuit. Turn ignition ON, with engine OFF. Observe IAT sensor temperature with a scan tool. Does the scan tool indicate IAT sensor temperature is greater than 280°F (138°C)? If yes, go to step 8. If no, see DIAGNOSTIC AIDS .
- Turn ignition OFF. Disconnect ECT sensor. Connect a 3-amp fused jumper wire between the ECT sensor signal circuit and a good ground. Turn ignition ON, with engine OFF. Observe ECT sensor temperature with a scan tool. Does the scan tool indicate ECT sensor temperature is greater than 280°F (138°C)? If yes, go to next step. If no, go to step 7.
- Test ECT sensor low reference circuit for an open or high resistance. Did you find and correct the condition? If yes, go to step 12.
- Test ECT sensor signal circuit for an open or high resistance. Did you find and correct the condition? If yes, go to step 12. If no, go to step 10.
- Remove ECT sensor. Suspend ECT sensor and a thermometer in a pan of water. Place the pan on a burner or hot plate. Test the resistance of the ECT sensor through 50-194°F (10-90°C). Does the resistance and temperature closely match the Temperature vs. Resistance table? See Figure. If yes, go to next step. If no, go to step 10.
- Reinstall ECT sensor. When complete, see DIAGNOSTIC AIDS .
- Test for an intermittent and/or poor connections at the ECT sensor. Did you find and correct the condition? If yes, go to step 12. If no, go to next step.
- Replace ECT sensor. See ENGINE COOLANT TEMPERATURE SENSOR under SENSORS in REMOVAL & INSTALLATION - CORVETTE article. Did you complete the replacement? If yes, go to next step.
- Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition cycle? If yes, go to step 2. If no, go to next step.
- Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.