SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001CAVALIER LS, 2.4 TREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2 (POWER MIRROR SYSTEM)DIAGNOSTIC TESTSDTC B2262: LEFT MIRROR HORIZONTAL POSITION SENSOR FAULT
2001 Chevrolet Cavalier LS, 2.4 T

DTC B2262: Left Mirror Horizontal Position Sensor Fault

2001 Chevrolet Cavalier LS, 2.4 TSECTION DTC B2262: Left Mirror Horizontal Position Sensor Fault
WARNING: This page is about a different car, the 2000 Chevrolet Corvette, 1999 Chevrolet Corvette, and 1998 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
  1. Perform DIAGNOSTIC SYSTEM CHECK  under SELF-DIAGNOSTIC SYSTEM. Go to next step.
  2. Using scan tool, select LDCM DTC display. If DTC B2262 is stored as a history code, go to next step. If DTC B2262 is not stored as a history code, go to step  8 .
  3. Using scan tool, select LDCM data display. Monitor horizontal position sensor data while operating left-side mirror. Mirror horizontal position sensor voltage should display 0.1-4.8 volts. If reading is not as specified, go to next step. If reading is as specified, check mirror horizontal position sensor circuit for poor connections or intermittent operation. See WIRING DIAGRAMS  . If mirror horizontal position sensor circuit checks okay, retest system. If DTC B2262 sets as a history code, go to step  11 .
  4. Turn ignition off. Disconnect left power mirror 4-pin connector C2. Turn ignition on. Using DVOM, check voltage between left power mirror harness connector C2 terminal "A" (Gray wire) and ground. See Fig 1 . If reading is 4.0-5.5 volts, go to next step. If reading is not 4.5-5.5 volts, go to step  7 .
  5. Check voltage between left power mirror harness connector C2 terminals "A" (Gray wire) and "C" (Black/White wire) while operating left-side mirror. If reading is 4.0-5.5 volts, go to next step. If reading is not 4.0-5.5 volts, go to step  9 .
  6. Replace left power mirror. See POWER MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. Recheck system operation.
  7. Check for open , short to ground or short to voltage in Gray wire between left power mirror connector C2 terminal "A" and Left Door Control Module (LDCM) connector C1 terminal No. 5. Repair as necessary. Recheck system operation. If circuit is okay, go to step  11 .
  8. Turn ignition off. Disconnect left power mirror 4-pin connector C2. Turn ignition on. Using DVOM, check voltage between left power mirror harness connector C2 terminal "D" (Gray wire) and ground while operating left-side mirror. See Fig 1 . If reading is 3.5-5.5 volts, go to step  6 . If reading is not 3.5-5.5 volts, go to step  10 .
  9. Check for open or short to voltage in Black/White wire between left power mirror connector C2 terminal "C" and LDCM connector C1 terminal No. 6. See Figure . Repair as necessary. Recheck system operation. If circuit is okay, go to step  11 .
  10. Check for open, short to ground or short to voltage in Gray wire between left power mirror connector C2 terminal "D" and Left Door Control Module (LDCM) connector C1 terminal No. 15. See Figure . Repair as necessary. Recheck system operation. If circuit is okay, go to next step.
  11. Replace LDCM. See DOOR CONTROL MODULE  under REMOVAL & INSTALLATION.
Fig 1: Power Mirror Connector C2 Terminal Identification
G00012600Courtesy of GENERAL MOTORS CORP.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.