Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2000CAB & CHASSIS C2500, 6.5 F, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1615 (VIBRATION SYMPTOMS DIAGNOSIS AND CORRECTION)
2000 Chevrolet Cab & Chassis C2500, 6.5 F, Automatic
Section 1615 (Vibration Symptoms Diagnosis And Correction)
2000 Chevrolet Cab & Chassis C2500, 6.5 F, AutomaticSECTION Section 1615 (Vibration Symptoms Diagnosis And Correction)
WARNING: This page is about a different car, the 2007 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Diagnostic Information and Procedures
- Diagnostic Starting Point - Vibration Diagnosis and Correction
- Vibration Analysis - Road Testing
- Component Rotational Speed Calculation
- Vibration Analysis - Tire and Wheel
- Vibration Analysis - Driveline
- Vibration Analysis - Hub and/or Axle Input
- Vibration Analysis - Engine
- Engine Order Classification
- Vibration Analysis - Engine/Accessory Isolation
- Vibration Analysis - Engine Balance
- Vibration Diagnostic Aids
- Vibration Diagnostic Aids - Vibration Intermittent or Not Duplicated
- Vibration Diagnostic Aids - Vibration Duplicated, Component Not Identified
- Vibration Diagnostic Aids - Vibration Duplicated, Difficult to Isolate/Balance Component
- Vibration Diagnostic Aids - Vibration Duplicated, Appears to Be Potential Operating Characteristic
- Symptoms - Vibration Diagnosis and Correction
- Vehicle-to-Vehicle Diagnostic Comparison
- Tire and Wheel Inspection
- Tire and Wheel Assembly Runout Measurement - On-Vehicle
- Tire and Wheel Assembly Runout Measurement - Off Vehicle
- Brake Rotor/Drum Balance Inspection
- Hub/Axle Flange and Wheel Stud Runout Inspection
- Tire and Wheel Assembly Isolation Test
- Vibration in Service-Stall Test (Non-Torque Sensitive)
- Vibration in Service-Stall Test (Torque Sensitive)
- Transfer Case Output Flange Runout Measurement
- Propeller Shaft Runout Measurement
- Torque Tube Input Flange Runout Measurement
- Pinion Flange Runout Measurement
- Differential Pinion Input Shaft Runout Measurement
- Driveline Working Angles Measurement
- Propeller Shaft Phasing Inspection
- Repair Instructions
- Tire and Wheel Assembly Balancing - Off Vehicle
- Tire and Wheel Assembly Balancing - On-Vehicle
- Tire-to-Wheel Match-Mounting (Vectoring)
- Tire and Wheel Assembly-to-Hub/Axle Flange Match-Mounting
- Driveline System Balance Adjustment (Using EVA)
- Driveline System Balance Adjustment (Without EVA)
- Driveline Working Angles Adjustment
- Propeller Shaft Phasing Correction
- Description and Operation
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.