Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET1998SUBURBAN K2500, 7.4 J, PART TIMEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 207 (AUTOMATIC TRANSAXLE SERVICING)TORQUE SPECIFICATIONS
1998 Chevrolet Suburban K2500, 7.4 J, Part Time
Torque Specifications
1998 Chevrolet Suburban K2500, 7.4 J, Part TimeSECTION Torque Specifications
WARNING: This page is about a different car, the 2003 Cadillac Seville and 2003 Cadillac DeVille. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |
|---|---|---|
| Case Cooler Connector (Return) | 21 (29) | |
| Case Cover-To-Case Bolt | ||
| 10 mm | 20 (27) | |
| 13 mm | 23 (31) | |
| Case Cover-To-Case Stud | ||
| 10 mm | 20 (27) | |
| 13 mm | 23 (31) | |
| Case Cover-To-Driven Sprocket Support Bolt | 20 (27) | |
| Case Extension-To-Case Bolt | ||
| 10 mm | 20 (27) | |
| 13 mm | 41 (55) | |
| Case Extension-To-Case Stud | 41 (55) | |
| Case-To-Forward Clutch Support Stud | 20 (27) | |
| Cooler Connector-To-Cooler (Case Cover) | 20 (27) | |
| Differential-To-Final Drive Carrier Bolt | 56 (76) | |
| Manual Shaft-To-Detent Lever Nut | 25 (34) | |
| Oil Test Case Cover Plug (No. 40 TORX(R)) | 19 (26) | |
| Side Cover-To-Case Cover Bolt | ||
| 13 mm | 20 (27) | |
| 15 mm | 41 (55) | |
| Side Cover-To-Case Cover Stud | 41 (55) | |
| Transaxle Mount-To-Bracket Nut (Left) | 55 (75) | |
| Transaxle Mount-To-Bracket Nut (Rear) | 30 (40) | |
| Transaxle Mount Bracket-To-Transaxle Bolt (Left) | 37 (50) | |
| Transaxle Mount Bracket-To-Transaxle Bolt (Rear) | 37 (50) | |
| Transaxle Mount-To-Frame Bolt and Nut (Rear) | 37 (50) | |
| Transaxle Mount-To-Frame Rail Nut (Left) | 52 (70) | |
| INCH Lbs. (N.m) | ||
| Accumulator Housing Cover Bolt | 124 (14) | |
| Accumulator Housing-To-Channel Plate Bolt | 124 (14) | |
| Bottom Pan-To-Case Bolt | 106 (12) | |
| Channel Plate-To-Accumulator Housing Bolt | 124 (14) | |
| Channel Plate-To-Case Bolt | 124 (14) | |
| Channel Plate-To-Case Nut | 124 (14) | |
| Detent Lever & Roller Assembly Bolt | 124 (14) | |
| Drive Sprocket Support-To-Case Bolt | 115 (13) | |
| Input Speed Sensor-To-Case Bolt | 115 (13) | |
| LCVB-To-Channel Plate Bolt | 124 (14) | |
| Oil Drain-Bottom Pan-To-Case Cover Plug | 124 (14) | |
| Oil Transfer Plate-To-Case Bolt | 124 (14) | |
| Pressure Control Solenoid Bracket-To-UCVB Bolt | 115 (13) | |
| Pump Assembly-To-Case Bolt | 115 (13) | |
| Pump Assembly-To-Case Cover Bolt | 115 (13) | |
| Scavenge Pump Cover-To-Scavenge Pump Body Bolt | 115 (13) | |
| Scavenge Tube-To-Case Bolt | 124 (14) | |
| Secondary Pump-To-Case Bolt | 115 (13) | |
| Secondary Pump-To-Case Cover Bolt | 115 (13) | |
| Servo Cover-To-Case Bolt | 124 (14) | |
| Spacer Plate Support-To-Channel Plate Bolt | 124 (14) | |
| Speed Sensor-To-Case Extension Bolt | 124 (14) | |
| Temperature Sensor | 30 (3.4) | |
| UCVB-To-Case Bolt | 115 (13) | |
| UCVB-To-Case Cover Bolt | 115 (13) | |
| UCVB-To-Driven Sprocket Support Bolt | 115 (13) | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.