Quick Lookups: Fluids

2013 Cadillac Escalade ESV Platinum, RWDSECTION Fluids
FLUID CAPACITIES
Fluid Type Application Standard Metric Fluid Spec Note S/H
Air Cond Compressor Oil Gas/Ethanol w/o Rear AC 7.10 OZS. 0.2 L PAG 46 S
Air Cond Compressor Oil Gas/Ethanol w/Rear A/C 11.00 OZS. 0.32 L PAG 46 S
Air Cond Refrigerant Front & Rear 2.50 LBS. 1.13 KG R-134a S
Air Cond Refrigerant Front 1.60 LBS. 0.72 KG R-134a S
Automatic Transmission Fluid Trans Mfr CD 6L80-E/MYC Complete Trans System (Heavy Duty Cooling) 12.40 QTS. 11.73 L Automatic Transmission Fluid DEXRON VI All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Automatic Transmission Fluid Trans Mfr CD 6L80-E/MYC Complete Trans System 12.20 QTS. 11.54 L Automatic Transmission Fluid DEXRON VI All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Automatic Transmission Fluid Trans Mfr CD 6L80-E/MYC Overhaul 10.50 QTS. 9.93 L Automatic Transmission Fluid DEXRON VI All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Automatic Transmission Fluid Trans Mfr CD 6L80-E/MYC Pan Removal & Filter Replacement 6.00 QTS. 5.67 L Automatic Transmission Fluid DEXRON VI All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Brake Fluid N/A N/A DOT 3 Hydraulic Brake Fluid S
Differential Gear Oil Front Axle 8.25" 1.51 QTS. 1.42 L SAE 80W-90 Gear Oil GM Part No. 89021671. All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Differential Gear Oil Front Axle 9.25" 1.83 QTS. 1.73 L SAE 80W-90 Gear Oil GM Part No. 89021671. All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Differential Gear Oil Rear Axle 10.5" 2.75 QTS. 2.6 L SAE 75W-90 Synthetic Gear Oil GM Part No. 89021671. All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Engine Coolant 17.60 QTS. 16.65 L 50/50 mixture of DEX-COOL and clean, drinkable water Add 2.1 qts. if equipped with rear heater. All capacities are approximate. When adding, be sure to fill to the approximate level. Recheck the fluid level after filling. S
Engine Oil w/Filter 6.00 QTS. 5.67 L API - SAE 5W-30 The engine requires engine oil approved to the dexos1 specification. Oils meeting this specification can be identified with the dexos certification mark. Look for and use only an engine oil that displays the dexos certification mark of the proper viscosity grade. SAE 5W-30 is the best viscosity grade for the vehicle. Do not use other viscosity oils such as SAE 10W-30, 10W-40, or 20W-50. Cold Temperature Operation: In an area of extreme cold, where the temperature falls below -29Deg. C (-20Deg. F), an SAE 0W-30 oil should be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, be sure to always select an oil that meets the required specification, dexos. S
Fuel Tank 26.00 GALS. 98.42 L S
Transfer Case Fluid 1.50 QTS. 1.41 L Automatic Transmission Fluid DEXRON VI S
Windshield Washer Fluid N/A N/A Windshield Washer Fluid Follow the Manufacturer's Instructions for the mixture ratio. Automotive windshield washer fluid that meets regional freeze protection requirements. S
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.