Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Circuit/System Testing
without Navigation System
- Ignition OFF, disconnect the GPS and cellular coax cable connector at the K73 Telematics Communication Interface Control Module.
- Using the EL-49903 OnStar Antenna Diagnostic Tool Kit , connect the EL-49903-3 antenna to the K73 Telematics Communication Interface Control Module. Place the test antenna on the roof of the vehicle, ignition ON.
- Verify that an OnStar advisor can locate the vehicle after performing a blue button press.
- If the advisor can not locate the vehicle
Replace the K73 Telematics Communication Interface Control Module.
- If the advisor can locate the vehicle
- If the advisor can not locate the vehicle
- Ignition OFF, disconnect the EL-49903 GM OnStar antenna diagnostic tool kit from the K73 Telematics Communication Interface Control Module
- Disconnect the K73 Telematics Communication Interface Control Module coax at the T4G Cellular Phone, Navigation, and Digital Radio Antenna.
- Test the coax cable between the K73 Telematics Communication Interface Control Module and the T4G Cellular Phone, Navigation, and Digital Radio Antenna. Refer to component testing.
- If the coax cable does not pass the test
Replace the coax cable.
- If the coax cable passes the test
- If the coax cable does not pass the test
- Test or replace the T4G Cellular Phone, Navigation, and Digital Radio Antenna.
with Navigation System
- Ignition OFF, disconnect the coax cable at the T15 Navigation Antenna Signal Splitter.
- Connect the EL-49903 OnStar Antenna Diagnostic Tool Kit to the T15 Navigation Antenna Signal Splitter. Place the test antenna on the roof of the vehicle, ignition ON.
- Verify that an OnStar advisor can not locate the vehicle after performing a blue button press.
- If the advisor can locate the vehicle
- Ignition OFF, disconnect the coax cable at the T4G Cellular Phone, Navigation, and Digital Radio Antenna.
- Test the coax cable between the T15 Navigation Antenna Signal Splitter and the T4G Cellular Phone, Navigation, and Digital Radio Antenna. Refer to Component Testing.
- If the coax cable does not pass the test
Replace the coax cable.
- If the coax cable passes the test
- If the coax cable does not pass the test
- Replace the T4G Cellular Phone, Navigation, and Digital Radio Antenna.
- If the advisor can not locate the vehicle
- Ignition OFF, disconnect the GPS and cellular coax cable connector at the K73 Telematics Communication Interface Control Module.
- Connect the EL-49903 OnStar Antenna Diagnostic Tool Kit to the K73 Telematics Communication Interface Control Module. Place the test antenna on the roof of the vehicle, ignition ON.
- Verify that an OnStar advisor can locate the vehicle after performing a blue button press.
- If the advisor can not locate the vehicle
Replace the K73 Telematics Communication Interface Control Module.
- If the advisor can locate the vehicle
- If the advisor can not locate the vehicle
- Ignition OFF.
- Test the coax cable between the T15 Navigation Antenna Signal Splitter and the K73 Telematics Communication Interface Control Module. Refer to Component Testing.
- If the coax cable does not pass the test
Replace the coax cable.
- If the coax cable passes the test
- If the coax cable does not pass the test
- Ignition OFF, disconnect the GPS coax cable at the K74 Human Machine Interface Control Module.
- Connect the EL-49903 OnStar Antenna Diagnostic Tool Kit to the K74 Human Machine Interface Control Module and place the test antenna on the roof of the vehicle.
- Ignition ON.
- Verify that the NO GPS symbol/message is not displayed on the P17 Display Module.
- If the NO GPS symbol/message is displayed
Replace the K74 Human Machine Interface Control Module
- If the NO GPS symbol/message is not displayed
- If the NO GPS symbol/message is displayed
- Ignition OFF.
- Test the coax cable between the T15 Navigation Antenna Signal Splitter and the K74 Human Machine Interface Control Module. Refer to Component Testing.
- If the coax cable does not pass the test
Replace the coax cable.
- If the coax cable passes the test
- If the coax cable does not pass the test
- Test or replace the T15 Navigation Antenna Signal Splitter.
Perform the Circuit/System Verification before proceeding with Circuit/System Testing.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.