SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC2011ESCALADE BASE, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSWIRING DIAGRAMSWIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - A/C COMPRESSOR THROUGH ELECTRONIC POWER STEERING MODULE X1COMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM) X5
2011 Cadillac Escalade Base, AWD

Body Control Module (BCM) X5

2011 Cadillac Escalade Base, AWDSECTION Body Control Module (BCM) X5
Fig 1: Body Control Module (BCM) X5 Connector End View
GM1664500Courtesy of GENERAL MOTORS CORP.
Body Control Module (BCM) X5

Pin Wire Circuit Function
1 0.5 YE/BK 1334 Left Rear Turn Signal Lamp Control (X88, Z88 or Z75, with EXP and with E52)
0.35 YE 18 Left Rear Stop/Turn Lamp Control (X88 without E52 or Z75 without EXP)
2 0.5 D-GN/WH 1335 Right Rear Turn Signal Lamp Control (X88, Z88 or Z75, with EXP and with E52)
1 D-GN 19 Right Rear Stop/Turn Lamp Control (X88 without E52 or Z75 without EXP)
3 - - Not Used
4 0.5 L-BU/WH 1314 Left Front Turn Signal Lamp Control
5 0.5 L-BU 1320 CHMSL Control
6 0.35 L-BU/WH 6311 Brake Signal
7 0.35 D-BU 38 Backup Lamp Control
8 0.5 PK 5076 Current Sensor Control
9 0.5 WH 5075 Current Sensor Signal
10 0.5 BN 5077 Low Reference
11 0.35 YE 43 Ignition Voltage
12 - - Not Used
13 0.35 OG 300 Ignition Voltage
14 0.35 WH 2283 Rear Wiper/Washer Switch Control (E52 or TB7)
15 0.35 PU 5531 Hood Closed Switch Signal
16 0.35 L-BU 1134 Park Brake Switch Signal
17 0.5 YE 5356 Left Tail Lamp Outage Detection Signal (Z75)
18 0.35 TN 28 Horn Relay Control
19 0.35 YE 6812 Out of Park Signal (except HP2)
20 0.35 GY 91 Windshield Wiper Switch Signal 2
21 0.35 TN 860 Front Windshield Wiper Switch High Signal
22 - - Not Used
23 0.35 PK/WH 1970 Headlamp Low Beam Relay Control
24 0.35 D-BU 45 Park Lamp Relay Control
25 - - Not Used
Connector Part Information
  • Harness Type: Instrument Panel
  • OEM Connector: 15480179
  • Service Connector: 88988837
  • Description: 25-Way F HIT Series (BN)
Terminal Part Information
  • Pins: 1-5
  • Terminated Lead: 13327199
  • Release Tool: J-38125-12A
  • Diagnostic Test Probe: J-35616-35 (VT)
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: Pins 1, 2 (X88, Z88 or Z75 with EXP and with E52), 4, 5 - E/A
  • Core/Insulation Crimp: Pins 2 (X88 without E52 or Z75 without EXP) - C/A
  • Pins: 6-25
  • Terminated Lead: 13575870
  • Release Tool: J-38125-12A
  • Diagnostic Test Probe: J-35616-64B (L-BU)
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.