Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC2008ESCALADE RWD V8-6.2LREPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGCOMPRESSOR HVACSERVICE AND REPAIRAIR CONDITIONING COMPRESSOR REPLACEMENT
2008 Cadillac Escalade RWD V8-6.2L
Air Conditioning Compressor Replacement
2008 Cadillac Escalade RWD V8-6.2LSECTION Air Conditioning Compressor Replacement
Compressor Replacement (LY2, LY5, LH6, L76, L92 and LMG)
Tools Required
J 39400-A Halogen Leak Detector
Removal Procedure
1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging.
2. Install a ratchet into the air conditioning (A/C) belt tensioner adapter opening.
3. Remove the air cleaner resonator outlet duct.
4. Rotate the A/C belt tensioner clockwise in order to relieve the tension on the belt.
5. Remove the A/C belt from the A/C compressor.
6. Slowly release the tension on the A/C belt tensioner.
7. Remove the discharge hose bolt from the A/C compressor.
8. Remove the discharge hose from the A/C compressor.
9. Remove the suction hose bolt from the A/C compressor.
10. Remove the suction hose from the A/C compressor.
11. Discard the sealing washers. Cap all of the openings.
12. Disconnect the electrical connections.
13. Remove the A/C compressor mounting bolts. The lower right bolt (3) will stay with the compressor due to a lack of clearance.
14. Remove the A/C compressor (2) from the bracket (1).
15. If replacing the A/C compressor. Refer to Compressor Oil Balancing.
Installation Procedure
1. Install the A/C compressor (2) to the bracket (1) through the fender well. Insert the mounting bolt (3) into the lower right mounting boss before installing the A/C compressor.
2. Install the A/C compressor to the bracket. Insert the mounting bolt into the lower right mount before installing the A/C compressor.
Notice: Refer to Fastener Notice.
3. Install the A/C compressor mounting bolts.
Tighten the bolts to 50 N.m (37 lb ft).
4. Connect the electrical connector to the A/C compressor.
5. Install the A/C discharge hose to the compressor using new sealing washers.
6. Install the A/C discharge hose bolt to the A/C compressor.
Tighten the bolt to 16 N.m (12 lb ft).
7. Install the A/C suction hose to the compressor using new sealing washers.
8. Install the A/C suction hose bolt to the A/C compressor.
Tighten the bolt to 16 N.m (12 lb ft).
9. Install the A/C drive belt.
10. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
11. Install the air cleaner resonator outlet duct.
12. Leak test the fittings of the component using the J 39400-A.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.