SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC2007XLR BASEREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTINFOTAINMENTCELLULAR SYSTEM, ENTERTAINMENT SYSTEM, AND NAVIGATION SYSTEMSPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2007 Cadillac XLR Base

Fastener Tightening Specifications

2007 Cadillac XLR BaseSECTION Fastener Tightening Specifications
Fastener Tightening Specifications

Application Specification
Metric English
Amplifier Bracket Retaining Screws 2.5 N.m 22 lb in
Antenna Buffer Retaining Screws 1.8 N.m 16 lb in
Antenna Ground Plate Bolts 10 N.m 89 lb in
Antenna Module Retaining Screws 1.8 N.m 16 lb in
Bose® Signal Processing Module Retaining Bolts 2.5 N.m 22 lb in
Communication Interface Module Screw 2 N.m 18 lb in
Digital Radio Receiver Mounting Bracket Nuts 9 N.m 80 lb in
Front Door Speaker Assembly Retaining Screws (Tighten in Sequence) 2.5 N.m 22 lb in
Front Speaker Retaining Screws 2.5 N.m 22 lb in
Front Windshield Antenna Coaxial Cable Ground Wire Bolt 1.8 N.m 16 lb in
Ignition Switch Retaining Bolts 5.5 N.m 49 lb in
Microphone Retaining Screws 2.5 N.m 22 lb in
Negative Battery Cable Bolt 15 N.m 11 lb ft
Radio Control Retaining Screws 2.5 N.m 22 lb in
Radio Fixed Antenna Long Braided Ground Strap Retaining Nut 5.8 N.m 51 lb in
Radio Fixed Antenna Mast 5 N.m 44 lb in
Radio Fixed Antenna Retaining Nuts 12 N.m 106 lb in
Radio Fixed Antenna Short Braided Ground Strap and Dual Cable Strap Retaining Nut 5.8 N.m 51 lb in
Radio Mounting Bracket Retaining Bolt 2.5 N.m 22 lb in
Radio Power Antenna Bracket Retaining Bolts 10 N.m 89 lb in
Radio Power Antenna Bracket Retaining Nuts 12 N.m 106 lb in
Radio Power Antenna Long Braided Ground Strap Retaining Nut 5.8 N.m 51 lb in
Radio Power Antenna Short Braided Ground Strap and Dual Cable Strap Retaining Nut 5.8 N.m 51 lb in
Rear Speaker Retaining Screws 2.5 N.m 22 lb in
Remote CD Changer Mounting Bracket Bolts 1.9 N.m 17 lb in
Remote CD Changer Mounting Nuts 12 N.m 106 lb in
Seat Speaker Retaining Screws 2.5 N.m 22 lb in
Taillamp Retaining Screws 2 N.m 18 lb in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.