Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC1996ELDORADO V8-4.6L VIN 9REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSCOOLING SYSTEMSYSTEM SPECIFICATIONS
1996 Cadillac Eldorado V8-4.6L VIN 9
System Specifications
1996 Cadillac Eldorado V8-4.6L VIN 9SECTION System Specifications
Component Torque/Ft. Lbs.
Belt Tensioner 35
Cam Cover 7
Camshaft Bearing Cap 9
Camshaft Drive Chain Tensioner 20
Camshaft Seal Retainer To Cover [01] 10
Camshaft Sprocket 90
Coolant Drain Plug 6
Cooling Fan Mounting Bolts 7
Cylinder Head Bolts [03]
Engine To Transmission 35
Exhaust Manifold To Cylinder Head Bolt 20
Exhaust Manifold To Cylinder Head Locknut 25
Flywheel [05] 11
Flywheel Housing Cover [01] 12
Front Cover 7
Fuel Filter Bolt [01] 88
Intake Manifold Bolts [01] [02] 71
Intake Manifold Cover Bolts [01] 106
Main Bearing Cap Bolts [03]
Oil Filter Adapter 20
Oil Pan 7
Oil Pan Drain Plug 15
Oil Pump To Lower Crankcase [06] 7
Oil Pump To Suction Pipe 7
Oxygen Sensor 30
Thermostat Housing Bolts 18
Throttle Body Bolts [01] 106
Torque Strut Bracket To Cylinder Head 35
Torque Strut Bracket To Water Manifold 20
Torsional Damper [04] 105
Transmission Brace 35
Water Pump Housing 20
Water Pump Pulley Mounting Bolts 22
Water Pump Stud Nuts [01] 62
[01] -- Inch pounds.
[02] -- Plus an additional 1/3 turn (120°).
[03] -- Refer to Cylinder Head Assembly/Service and Repair
[04] -- Plus an additional 120° rotation.
[05] -- Plus an additional 50° rotation.
[06] -- Plus an additional 35° rotation.
Belt Tensioner 35
Cam Cover 7
Camshaft Bearing Cap 9
Camshaft Drive Chain Tensioner 20
Camshaft Seal Retainer To Cover [01] 10
Camshaft Sprocket 90
Coolant Drain Plug 6
Cooling Fan Mounting Bolts 7
Cylinder Head Bolts [03]
Engine To Transmission 35
Exhaust Manifold To Cylinder Head Bolt 20
Exhaust Manifold To Cylinder Head Locknut 25
Flywheel [05] 11
Flywheel Housing Cover [01] 12
Front Cover 7
Fuel Filter Bolt [01] 88
Intake Manifold Bolts [01] [02] 71
Intake Manifold Cover Bolts [01] 106
Main Bearing Cap Bolts [03]
Oil Filter Adapter 20
Oil Pan 7
Oil Pan Drain Plug 15
Oil Pump To Lower Crankcase [06] 7
Oil Pump To Suction Pipe 7
Oxygen Sensor 30
Thermostat Housing Bolts 18
Throttle Body Bolts [01] 106
Torque Strut Bracket To Cylinder Head 35
Torque Strut Bracket To Water Manifold 20
Torsional Damper [04] 105
Transmission Brace 35
Water Pump Housing 20
Water Pump Pulley Mounting Bolts 22
Water Pump Stud Nuts [01] 62
[01] -- Inch pounds.
[02] -- Plus an additional 1/3 turn (120°).
[03] -- Refer to Cylinder Head Assembly/Service and Repair
[04] -- Plus an additional 120° rotation.
[05] -- Plus an additional 50° rotation.
[06] -- Plus an additional 35° rotation.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.