Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC1996ELDORADO V8-4.6L VIN 9REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONCOMPONENT TESTS AND GENERAL DIAGNOSTICSALCOHOL/CONTAMINANTS-IN-FUEL TESTING PROCEDURE
1996 Cadillac Eldorado V8-4.6L VIN 9
Alcohol/Contaminants-In-Fuel Testing Procedure
1996 Cadillac Eldorado V8-4.6L VIN 9SECTION Alcohol/Contaminants-In-Fuel Testing Procedure
DESCRIPTION
Alcohol-in-fuel can be detrimental to fuel system components and may cause driveability problems such as hesitation, lack of power, stall or no start. The problems may be due to fuel system corrosion and subsequent fuel filter plugging, deterioration of rubber components and/or air-fuel mixture leaning.
Various types and concentrations of alcohols are used in commercial fuel. Some alcohols are more detrimental to fuel system components than others. If an excessive amount of alcohol in the fuel is suspected as the cause of a driveability condition, the following procedure may be used to detect the presence of alcohol in the fuel.
SAMPLING PROCEDURE
The fuel sample should be drawn from the bottom of the tank so that any water present in the tank can be detected. The sample should be bright and clear. If the sample appears cloudy or contaminated with water (as indicated by a water layer in the bottom of the sample), this procedure should not be used and the fuel system should be cleaned.
TESTING PROCEDURE
1. Using a 100 ml cylinder with 1 ml graduation marks, fill with fuel to the 90 ml mark.
2. Add 10 ml of water to bring the total fluid volume to 100 ml and install a stopper.
3. Shake vigorously for 10 to 15 seconds.
4. Carefully loosen the stopper and release the pressure.
5. Close the stopper and shake vigorously again for 10 to 15 seconds.
6. Put the graduated cylinder on a level surface for approximately 5 minutes to allow time for adequate liquid separation.
INTERPRETING TEST RESULTS
If alcohol is present in the fuel, the volume of the lower layer, which would now contain alcohol and water, will be greater than 10 ml. For example, if the volume of the lower layer is increased to 15 ml it would indicate at least 5 percent alcohol in the fuel. The actual amount of alcohol may be somewhat greater because this procedure does not extract all of the alcohol from the fuel.
Alcohol-in-fuel can be detrimental to fuel system components and may cause driveability problems such as hesitation, lack of power, stall or no start. The problems may be due to fuel system corrosion and subsequent fuel filter plugging, deterioration of rubber components and/or air-fuel mixture leaning.
Various types and concentrations of alcohols are used in commercial fuel. Some alcohols are more detrimental to fuel system components than others. If an excessive amount of alcohol in the fuel is suspected as the cause of a driveability condition, the following procedure may be used to detect the presence of alcohol in the fuel.
SAMPLING PROCEDURE
The fuel sample should be drawn from the bottom of the tank so that any water present in the tank can be detected. The sample should be bright and clear. If the sample appears cloudy or contaminated with water (as indicated by a water layer in the bottom of the sample), this procedure should not be used and the fuel system should be cleaned.
TESTING PROCEDURE
1. Using a 100 ml cylinder with 1 ml graduation marks, fill with fuel to the 90 ml mark.
2. Add 10 ml of water to bring the total fluid volume to 100 ml and install a stopper.
3. Shake vigorously for 10 to 15 seconds.
4. Carefully loosen the stopper and release the pressure.
5. Close the stopper and shake vigorously again for 10 to 15 seconds.
6. Put the graduated cylinder on a level surface for approximately 5 minutes to allow time for adequate liquid separation.
INTERPRETING TEST RESULTS
If alcohol is present in the fuel, the volume of the lower layer, which would now contain alcohol and water, will be greater than 10 ml. For example, if the volume of the lower layer is increased to 15 ml it would indicate at least 5 percent alcohol in the fuel. The actual amount of alcohol may be somewhat greater because this procedure does not extract all of the alcohol from the fuel.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.