SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBUICK2019ENVISION BASEREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTCELLULAR, ENTERTAINMENT, AND NAVIGATION SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESDTC B1277CIRCUIT/SYSTEM TESTING
2019 Buick Envision Base

Circuit/System Testing

2019 Buick Envision BaseSECTION Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the B24 Cellular Phone Microphone. Ignition On/Vehicle in Service Mode.
  2. Test for 9 - 11 V between the signal circuit terminal B and ground.
    • If less than 9 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K74 Human Machine Interface Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K74 Human Machine Interface Control Module.
    • If greater than 11 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K74 Human Machine Interface Control Module. Ignition On/Vehicle in Service Mode.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V, replace the K74 Human Machine Interface Control Module.
    • Go to next step: If between 9 - 11 V 
  3. Test for less than 1 V between the signal circuit terminal A and ground.
    • If greater than 1 V 
    1. Ignition OFF, X1 harness connector at the K74 Human Machine Interface Control Module. Ignition On/Vehicle in Service Mode.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage in the circuit.
      • If less than 1 V, replace the K74 Human Machine Interface Control Module.
    • Go to next step: If less than 1 V 
  4. Ignition OFF, disconnect the X1 harness connector at the K74 Human Machine Interface Control Module.
  5. Test for infinite resistance between the B24 Cellular Phone Microphone signal circuit terminal A and ground.
    • If less than infinite resistance 

      Repair the short to ground in the circuit

    • Go to next step: If infinite resistance 
  6. Test for less than 2 Ω in the signal circuit end to end.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit

    • Go to next step: If less than 2 Ω 
  7. Replace the B24 Cellular Phone Microphone.
  8. Ignition On/Vehicle in Service Mode.
  9. Verify the DTC does NOT set.
    • If the DTC sets 

      Replace the K74 Human Machine Interface Control Module

    • Go to next step: If the DTC does not set 
  10. All OK.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.