Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSBUICK2013REGAL TURBO PREMIUM, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 55 (CELLULAR SYSTEM, ENTERTAINMENT SYSTEM, AND NAVIGATION SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESAUXILIARY AUDIO INPUT MALFUNCTIONCIRCUIT/SYSTEM TESTINGAUXILIARY AUDIO INPUT JACK WITHOUT KTA
2013 Buick Regal Turbo Premium, Standard Trans
Auxiliary Audio Input Jack without KTA
2013 Buick Regal Turbo Premium, Standard TransSECTION Auxiliary Audio Input Jack without KTA
WARNING: This page is about a different car, the 2011 Buick Regal. However, it is still accessible from the selected car via links, so may be relevant.
- Ignition OFF, disconnect the X1 harness connector at the X83 auxiliary audio input.
- Ignition ON, radio ON, test for 2.5-3.5 V between the auxiliary detection terminal 1 and ground.
- If less than specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the A11 radio.
- If greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the A11 radio.
- Ignition OFF, disconnect the X1 harness connector at the radio. Test for infinite resistance between the circuits listed below and ground:
- auxiliary audio common circuit terminal 23
- left auxiliary audio circuit terminal 24
- right auxiliary audio circuit terminal 10
- If not the specified value, test the signal circuit for a short to ground.
- Test for less than 5 Ξ© between the A11 radio X1 terminal 24 and the X83 auxiliary audio input X1 terminal 2.
- If greater than the specified value, test the signal circuit for an open/high resistance.
- Test for less than 5 Ξ© between the A11 radio X1 terminal 10 and the X83 auxiliary audio input X1 terminal 4.
- If greater than the specified value, test the signal circuit for an open/high resistance.
- Test for less than 5 Ξ© between the A11 radio X1 terminal 23 and the X83 auxiliary audio input X1 terminal 5.
- If greater than the specified value, test the signal circuit for an open/high resistance.
- Reconnect the X1 harness connector at the A11 radio.
- Ignition ON, test for less than 1 V between the circuits listed below and ground:
- auxiliary audio common circuit X83 auxiliary audio input X1 terminal 5
- left auxiliary audio circuit X83 auxiliary audio input X1 terminal 2
- right auxiliary audio circuit X83 auxiliary audio input X1 terminal 4
- If greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the A11 radio.
- If all circuits test normal, replace the X83 auxiliary audio input and reconnect all harness connectors. Connect and operate the portable audio playback device. If audio cannot be heard from the device, replace the A11 radio.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.