SYS.OK|MANUAL.DBâ—Ź LIVE
HOMESERVICE MANUALSBUICK2011ENCLAVE CXL, FWDREPAIR AND DIAGNOSISELECTRICALCHARGING SYSTEMSBATTERY, CHARGING SYSTEM AND STARTING SYSTEMREPAIR INSTRUCTIONSBATTERY POSITIVE JUNCTION BLOCK CABLE REPLACEMENTINSTALLATION PROCEDURE
2011 Buick Enclave CXL, FWD

Installation Procedure

2011 Buick Enclave CXL, FWDSECTION Installation Procedure
    Fig 1: Identifying Battery Positive Junction Block Cable
    GM1861224Courtesy of GENERAL MOTORS CORP.
  1. Install the battery positive junction block cable to the vehicle.
    2. Fig 2: Identifying Accessory Wiring Junction Block Cover & Nut
    GM1861038Courtesy of GENERAL MOTORS CORP.
  2. Install the battery positive junction block cable terminal (4) to the stud.
  3. Install the positive battery cable terminal (3) to the junction block stud.
    4. CAUTION:

    Refer to Fastener Caution .

  4. Install the accessory wiring junction block nut (2).

    Tighten 

    Tighten the nut to 22 N.m (16 lb ft).

  5. Close the accessory wiring junction block cover (1).
    6. Fig 3: Identifying Battery Positive Junction Block Cable Clips
    GM1861223Courtesy of GENERAL MOTORS CORP.
  6. Install the battery positive junction block cable clips (1) to the power steering reservoir bracket.
    7. Fig 4: Identifying Battery Positive Junction Block Cable Boot & Cable Terminal
    GM1861163Courtesy of GENERAL MOTORS CORP.
  7. Install the battery positive junction block cable terminal (3) to the generator stud.
  8. Install the battery positive junction block cable to generator nut (3).

    Tighten 

    Tighten the nut to 22 N.m (16 lb ft).

  9. Position the battery positive junction block cable boot (1).
  10. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
    11. Fig 5: View Of Battery Positive Junction Block Cable Clip & Cable Terminal
    GM1861148Courtesy of GENERAL MOTORS CORP.
  11. Install the battery positive junction block cable terminal (2) to the starter.
  12. Install the starter solenoid BAT terminal nut (3).

    Tighten 

    Tighten the nut to 25 N.m (18 lb ft).

  13. Install the battery positive junction block cable clip (1) to the engine block.
    14. Fig 6: Identifying Starter Heat Shield Bolt & Shield
    GM1861146Courtesy of GENERAL MOTORS CORP.
  14. Install the starter heat shield and bolt.

    Tighten 

    Tighten the bolt to 7 N.m (62 lb in).

  15. Install the left catalytic converter. Refer to Catalytic Converter Replacement - Left Side .
  16. Install the fuel injector sight shield. Refer to FUEL INJECTOR SIGHT SHIELD REPLACEMENT .
  17. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.