SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBUICK2010LUCERNE CXL, 3.9 1REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 314 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - 1-2 SHIFT SOLENOID THROUGH ENGINE CONTROL MODULE X1)COMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM) X4
2010 Buick Lucerne CXL, 3.9 1

Body Control Module (BCM) X4

2010 Buick Lucerne CXL, 3.9 1SECTION Body Control Module (BCM) X4
WARNING: This page is about a different car, the 2011 Cadillac DTS. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Body Control Module (BCM) X4 Connector End View
GM1664499Courtesy of GENERAL MOTORS COMPANY
Body Control Module (BCM) X4

Pin Wire Circuit Function
1 0.8 RD/YE 340 Battery Positive Voltage
2 0.8 TN/PK 5040 Battery Positive Voltage
3 0.8 RD/GN 440 Battery Positive Voltage
4 0.8 YE/VT 1240 Battery Positive Voltage
5 0.8 D-BU/WH 1315 Right Front Turn Signal Lamp Supply Voltage
6 - - Not Used
7 1 YE 196 Windshield Wiper Motor Park Switch Signal
8 - - Not Used
9 0.35 BK 50 Ground
10 0.35 TN/OG 3640 Battery Positive Voltage
11 0.35 D-GN/WH 1317 Fog Lamp Relay Control
12-13 - - Not Used
14 0.35 L-GN 482 Outside Moisture Sensor Signal 2 (CE1)
15 0.35 OG/GY 227 Windshield Washer Relay Control
16 0.35 TN/WH 1969 Headlamp High Beam Relay Control
17 0.35 PK/BK 109 Hood Ajar Switch Signal
18 0.35 TN/YE 481 Outside Moisture Sensor Signal 1 (CE1)
19 0.35 D-BU/WH 5985 Accessory Wake up Serial Data
20 0.35 D-BU 6561 Right Cornering Lamp Relay Control
21 0.35 PK 1439 Run/Crank Ignition 1 Voltage
22-23 - - Not Used
24 0.35 BN 6560 Left Cornering Lamp Relay Control
25 0.35 WH 1080 Park Lamp Relay Control
Connector Part Information
  • Harness Type: BCM Jumper
  • OEM Connector: HITPB-25-D-K
  • Service Connector: 88988841
  • Description: 25-Way F HIT Series (BK)
Terminal Part Information
  • Pins: 1-5
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: E/A
  • Release Tool/Test Probe: 12094429/J-35616-4A (PU)
  • Pins: 7, 9-11, 14-21, 24, 25
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: 12094429/J-35616-64B (L-BU)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.