SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBUICK2006TERRAZA CXL, 3.5 L, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 46 (ANTILOCK BRAKE SYSTEM, TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC C0875TEST DESCRIPTION
2006 Buick Terraza CXL, 3.5 L, AWD

Test Description

2006 Buick Terraza CXL, 3.5 L, AWDSECTION Test Description
WARNING: This page is about a different car, the 2005 Buick LaCrosse and 2005 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step tests for specified voltage on the 5-volt reference signal circuit.
  2. 3:  This step checks to see if voltage was below specified voltage.
  3. 4:  This step checks to see if voltage was above specified voltage.
  4. 5:  This step tests for a short to ground in the 5-volt reference circuit of the yaw/lateral accelerometer sensor.
  5. 6:  This step tests for a short to voltage in the 5-volt reference circuit of the yaw/lateral accelerometer sensor.
  6. 7:  This step tests for a high resistance or an open in the ground circuit of the yaw/lateral accelerometer sensor.
  7. 8:  This step checks the yaw/lateral accelerometer sensor connector for poor connections.
  8. 9:  This step checks the EBCM connector for poor connections.
DTC C0875

Step Action Values Yes No
Schematic Reference: ABS Schematics 
Connector End View Reference: ABS Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Turn OFF the ignition.
  2. Disconnect the electronic brake control module (EBCM).
  3. Install the J 39700  Universal Pinout Box with the J 39700-530 Cable Adapter between the EBCM and the EBCM harness connector. See Special Tools .
  4. Turn ON the ignition, with the engine OFF.
  5. Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  . See Special Tools .
Is the voltage within the specified value?		 2.1-2.9 V Go to Diagnostic Aids Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the yaw/lateral accelerometer sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  . See Special Tools .
Is the voltage greater than the specified value?		 2.1 V Go to Step 4  Go to Step 5 
4  Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  . See Special Tools .
Is the voltage less than the specified value?		 2.9 V Go to Step 8  Go to Step 6 
5  Test the 5-volt reference circuit of the yaw/lateral accelerometer sensor for a short to ground. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
6  Test the 5-volt reference circuit of the yaw/lateral accelerometer sensor for a short to voltage. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 7 
7  Test the ground circuit of the yaw/lateral accelerometer sensor for a high resistance or an open. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
8  Inspect for poor connections at the harness connector of the yaw/lateral accelerometer sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 10 
9  Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections andConnector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 11 
10 Replace the yaw/lateral accelerometer sensor. Refer to Yaw Rate Sensor/Lateral Accelerometer Replacement .
Did you complete the replacement?		 - Go to Step 12  -
11 Replace the EBCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting test.
Does the DTC reset?		 - Go to Step 2  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.