Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSBUICK2005LESABRE LIMITED, 4T65E/M15REPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROLS - INTRODUCTIONCOMPONENT LOCATORENGINE CONTROLS COMPONENT VIEWS
2005 Buick LeSabre Limited, 4T65E/M15
Engine Controls Component Views
2005 Buick LeSabre Limited, 4T65E/M15SECTION Engine Controls Component Views
| Callout | Component Name |
|---|---|
| 1 | Powertrain Control Module (PCM) C1 |
| 2 | Powertrain Control Module (PCM) C2 |
| 3 | Air Cleaner Assembly |
| 4 | Powertrain Control Module (PCM) |
| 5 | S105 |
| Callout | Component Name |
|---|---|
| 1 | Intake Air Temp (IAT) Sensor |
| 2 | Cruise Control Module |
| 3 | Air Cleaner Assembly |
| Callout | Component Name |
|---|---|
| 1 | Manifold Absolute Pressure (MAP) Sensor |
| Callout | Component Name |
|---|---|
| 1 | Fuel Injector 3 |
| 2 | Evaporative Emissions (EVAP) Purge Canister |
| 3 | Fuel Injector 5 |
| 4 | Idle Air Control (IAC) Valve |
| 5 | Throttle Position (TP) Sensor |
| 6 | Mass Air Flow (MAF) Sensor |
| 7 | S106 |
| 8 | Engine Coolant Temp (ECT) Sensor |
| 9 | C103 |
| 10 | S108 |
| 11 | S107 |
| 12 | Ignition Control Module (ICM) |
| 13 | To Manifold Absolute Pressure (MAP) Sensor |
| 14 | Fuel Injector 1 |
| Callout | Component Name |
|---|---|
| 1 | Exhaust Gas Recirculation (EGR) Valve |
| 2 | Fuel Injector #6 |
| 3 | Fuel Injector #4 |
| 4 | Fuel Injector #2 |
| 5 | To Generator |
| 6 | To Air Solenoid |
| 7 | Heated Oxygen Sensor (H02S) Bank 1 Sensor 1 |
| 8 | S103 |
| 9 | S104 |
| 10 | To PCM |
| 11 | C100 |
| Callout | Component Name |
|---|---|
| 1 | Engine Oil Pressure Sensor |
| 2 | Vehicle Speed Sensor (VSS) |
| 3 | Power Steering Pressure Sensor |
| 4 | C125 |
| Callout | Component Name |
|---|---|
| 1 | Knock Sensor |
| 2 | Starter Solenoid |
| Callout | Component Name |
|---|---|
| 1 | Evaporative Emissions (EVAP) Canister Purge Valve |
| 2 | Generator |
| 3 | MAP Sensor |
| Callout | Component Name |
|---|---|
| 1 | Fuel Tank Pressure (FTP) Sensor |
| 2 | Fuel Pump and Sender Assembly |
| 3 | Fuel Pump Strainer |
| 4 | Fuel Level Sensor |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.