Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2023M550I XDRIVEREPAIR AND DIAGNOSISENGINE MECHANICALLUBRICATION SYSTEMENGINE - OIL FILTER & FILLING/OIL COOLING/COOLANT PUMP - REPAIR (G30)
2023 BMW M550i xDrive
Engine - Oil Filter & Filling/Oil Cooling/Coolant Pump - Repair (G30)
2023 BMW M550i xDriveSECTION Engine - Oil Filter & Filling/Oil Cooling/Coolant Pump - Repair (G30)
- 11 42 Oil Filter And Pipes
- 11 42 320 Replace oil spray nozzle (M550i xDrive, 2018-2019)
- Layout of main bearing caps
- Main bearing cap taper screw mounting
- Unscrew the threaded bushing
- Unscrew the collar screws M8
- Release the collar screws M11
- Removing the oil nozzle in the crankcase
- Install the oil nozzle in the crankcase
- Observe the bearing shell classification
- Rotate the threaded support sleeves in reverse
- Main bearing cap/thrust bearing
- Insert the crankshaft with the main bearing cap
- Screw in the collar screws M11
- Securing the collar screws M8
- Installation note for securing collar screws M11
- Secure the threaded support sleeve
- Secure the main bearing taper screw mounting
- Measure the coefficient of friction
- Check the crankshaft side clearance with the special tool
- Check the crankshaft side clearance
- 11 42 350 Removing and installing/replacing both oil feed lines (M550i xDrive, 2018-2019)
- 11 42 350 Removing and installing/replacing both oil feed lines (M550i xDrive, 2020-2022)
- 11 42 352 Expand and install/replace oil return lines (M550i xDrive, 2020-2022)
- 11 42 320 Replace oil spray nozzle (M550i xDrive, 2018-2019)
- 11 43 Oil Filling, Measuring Stick
- 11 44 Oil Cooler W Feed And Discharge Lines
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (530e PHEV, 2018-2020, 530e xDrive PHEV, 2018-2020)
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (540i, 2017-2020, 540i, 2021-2022)
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (540i xDrive, 2017-2020)
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (540i xDrive, 2021-2022)
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (M550i xDrive, 2018-2019)
- 11 44 000 Removing and installing, sealing replacing oil coolant heat exchanger (M550i xDrive, 2020-2022)
- 11 51 Coolant Pump With Drive
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.