Install the front left and right wheels

Mounting the wheel 

• Remove dirt, grease residues and corrosion from the contact surface with a drill and the special tool  2 344 011  .

  Do not operate special tool 2 344 011 with an impact screwdriver.

• Degrease the contact surfaces with the universal cleaner (see applicable BMW Group Parts catalog).
• In the event of grease residues in the area of the wheel bolt holes, remove and clean the brake disk.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Remove dirt, grease residues and corrosion from the contact surface with a drill and the special tool  2 344 011  .

  Do not operate special tool 2 344 011 with an impact screwdriver.

• Degrease the contact surfaces with the universal cleaner (see applicable BMW Group Parts catalog).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check if the mounting bolt (1) has been fitted correctly for the brake disk.

  The mounting bolt (1) for the brake disk cannot  protrude on the contact surface (2) between the brake disk and the rim.

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  Do not  grease the wheel hubs and wheel centering in models G80, G82 and G83.
• Lightly grease the wheel centering (1) in the rim.
  CONSUMABLE SPECIFICATION
  
  

  Brake block paste  * TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only.	3 g, Bag	83192158851
  	100 g, Tube	83192158852
  	5 g, TU*	83230140233

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  Do not  grease the wheel hubs and wheel centering in models G80, G82 and G83.
• Apply a thin layer of grease to the front and rear wheel hubs (1) to protect against corrosion.
  CONSUMABLE SPECIFICATION
  
  

  Brate block paste  * TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only.	3 g, Bag	83192158851
  	100 g, Tube	83192158852
  	5 g, TU*	83230140233

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  A wheel lifter is recommended for easier wheel removal and installation without exertion (see applicable Dealer Equipment Catalog).
• In vehicles with M Carbon ceramic brake: The wheel lifter must be used to install the wheel. 

  This process is intended to prevent damage to the brake disc.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Check 

• Check lug bolts for wear. 

  Courtesy of BMW OF NORTH AMERICA, INC.

  Result 

  » Spots (> 30%) of the bearing surface (1) of the taperon the screw head show silvery wear.

  Measure

  • Replace lug bolts.
  NOTE: TECHNICAL INFORMATION 
  Never use an impact screwdriver or electric screwdriver to apply and tighten the lug bolts.
  The rim must rest evenly against the brake disc.
  In the case of non-original BMW lug bolts/wheel rims, it may be necessary to retighten the lug bolts on user account of setting properties (refer to the documentation from the manufacturer).
  Do not apply oil to new lug bolts.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the corroded lug bolts (arrows).
• Clean wheel bolts (arrows).
• Check lug bolts (arrows) and threads for damage, replace lug bolts (arrows) if necessary.
• Join and tighten the lug bolts (arrows).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Lug bolts
  M14/SW17 Screw in lug bolts and evenly tighten crosswise by hand in order to center the wheel rim. Tighten lug bolts to the prescribed tightening torque with a calibrated torque wrench in a crosswise sequence. Check all the lug bolts in the same order or retighten to the prescribed tightening torque again.	tightening torque	140 Nm
  	Check	140 Nm