Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2021X2 XDRIVE28IREPAIR AND DIAGNOSISENGINE MECHANICALSTARTERENGINE ELECTRICAL SYSTEM -- REPAIR X2 (F39)
2021 BMW X2 xDrive28i
Engine Electrical System -- Repair X2 (F39)
2021 BMW X2 xDrive28iSECTION Engine Electrical System -- Repair X2 (F39)
- 12 00 Engine Electrical System
- 12 12 Ignition Wire, Spark Plugs
- 12 13 Ignition Coil
- 12 14 Electronic Switching Or Control Units
- 12 14 521 Replacing crankshaft pulse sensor (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 14 523 Replacing the camshaft position sensor (pulse sensor) of the intake camshaft (after vehicle diagnosis) (X2 2018-2023)
- 12 14 524 Replacing the camshaft position sensor (pulse sensor) of the exhaust camshaft (after vehicle diagnosis) (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 14 550 Replacing the control unit of the Digital Motor Electronics (After vehicle diagnosis) (X2 2018-2023)
- 12 14 602 Replacing knock sensor (after vehicle diagnosis) (cyl. 1-2) (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 14 604 Replacing knock sensor (after vehicle diagnosis) (cyl. 3-4) (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- Programming the control unit (DME/DDE) (X2 2018-2023)
- Replace crankshaft sensor (after vehicle diagnosis) (X2 M35i 2019-2022)
- 12 14 524 Replacing the exhaust camshaft position sensor (after vehicle diagnosis) (X2 M35i 2019-2022)
- 12 14 602 Replacing knock sensor (after vehicle diagnosis) (cyl. 1-2) (X2 M35i 2019-2022)
- 12 14 604 Replacing knock sensor (after vehicle diagnosis) (cyl. 3-4) (X2 M35i 2019-2022)
- 12 31 Alternator With Drive And Attachment
- 12 41 Starter With Attachment
- 12 42 Starter Line
- 12 51 Engine Wiring Harness
- 12 51 210 Replacing the wiring harness section for injectors and ignition coils (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 51 215 Replacing wiring harness section for Valvetronic actuator (X2 2018-2023)
- 12 51 235 Remove and install/replace Module 1, sensor system engine wiring (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 51 240 Remove and install/replace Module 2, sensor system engine wiring (X2 sDrive 28i 2018-2023, X2 xDrive 28i 2018-2023)
- 12 51 210 Replacing the wiring harness section for injectors and ignition coils (X2 M35i 2019-2022)
- 12 51 235 Remove and install/replace Module 1, sensor system engine wiring (X2 M35i 2019-2022)
- 12 51 240 Remove and install/replace Module 2, sensor system engine wiring (X2 M35i 2019-2022)
- 12 61 Oil Pressure, Oil Temp, Oil Level Check
- 12 63 Switch And Relay
- 12 90 E-Box
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.