Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
41 00... Welding And Soldering Steel Parts
Comply with the following topics from "Body, General":
Safety regulations . Refer to 41 00... Information on hazards and 41 00... Safety At Work .
Handling electrical/electronic equipment, airbags and restraint systems . Refer to 41 00... Handling Airbags And Restraint Systems and 41 00... Handling Electrical And Electronic Equipment .
- Welding steel parts:
- General information
- The following procedures are used for repairs:
- MAG welding (Metal Active Gas welding)
- Resistance pressure spot welding (referred to in the following and in the repair instructions as spot welding).
- Take the number and location of weld spots and MAG weld seams from the separated part. Replace areas inaccessible to spot-welding tongs with MAG plug/spot welds at the same distance. Diameter of bores for plug/spot welds 8 mm.
- In the case of emissions extraction, observe a minimum distance of 30 cm for MAG welding during the welding process. Otherwise the inert gas would be drawn off.
- Follow the equipment manufacturer's instructions for use.
- The following procedures are used for repairs:
- Work materials
- MAG welding:
- Steel welding apparatus (see WORKSHOP EQUIPMENT ).
- Steel welding wire - G3SI1 (SG2) or alternatively G4SI1 (SG3)
- Welding mask
- Gas bottle containing inert gas (82% argon, 18% CO2 )
- Resistance pressure spot welding:
- Spot-welding apparatus (see WORKSHOP EQUIPMENT ).
- Protective goggles
- MAG welding:
- Preparations for MAG and spot-welding
- Remove the paint coating in an area of approx. 30 mm around the weld seam or spot.
- The zinc coating underneath must be removed during the MAG welding operation.
- It is not necessary to remove the zinc coating underneath during spot-welding.
- Remove the paint coating on the reverse side of the weld seam or spot.
- Contaminants will otherwise enter the weld pool via the root of the weld seam.
- An insufficient electron flow prevents an optimum spot-weld joint.
- Coat all metal overlaps and weld spot flanges with welding primer.
- To determine the optimum electrode contact force for spot-welding, carry out spot-weld shear tests on sample metal sheets.
- In order to keep the electron flow short during MAG welding on the body, you must if possible attach the ground terminal directly to the component to be welded.
- Remove the paint coating in an area of approx. 30 mm around the weld seam or spot.
- Welding
- During MAG welding, the weld gap must be kept as small as possible. The larger the weld gap, the lower will be the strength of the joint.
- During spot-welding, the metal flanges to be joined must be placed as close together as possible without gaps.
The larger the gap, the lower will be the strength of the joint.
Minimum gap between welding spots 25 mm.
- Subsequent treatment of weld joints:
- When grinding a weld seam, do not grind thin the base material next to the seam.
- After joining, clean all weld seams and spots with a stainless steel wire brush.
- Remove burnt paint with a stainless steel wire brush.
- All weld joints sealed off with body sealing compound in original state must be primed and sealed off again thoroughly after repairing. Replace damaged or removed antinoise compounds.
- General information
- Soldering steel parts:
- General information
- The following procedures are used for repairs:
- Gas brazing
- Tinning
- The MIG soldering procedure is not used in repairs for strength reasons. MIG soldered/brazed seams used in series production are replaced in repairs by MAG weld seams.
- Areas brazed in vehicle production are joined during repairs with the same procedure.
- It is possible when straightening steel parts to correct irregularities smaller than 2 mm with filler.
If in exceptional cases the irregularities are in excess of 2 mm, these areas must be tinned.
Only visible areas of the outer skin and on the support carrier must be tinned.
All areas which have covers on the vehicle are not to be tinned.
NOTE: Only applicable within the European Union!European used-car regulations prohibit the use of tin containing lead in motor vehicles introduced after 01.07.2003!
- The following procedures are used for repairs:
- Work materials
- Gas brazing:
- Tube pack and torch (gas torch)
- Brazing solder
- Gas bottles (oxygen and acetylene)
- Welding goggles
- Tinning:
- Tube pack and torch (torch for tinning)
- Tinning paste
- Tin (refer to "Electronic Parts Catalogue" ETK).
- Gas bottle (acetylene)
- Protective goggles
- Gas brazing:
- Preparations for brazing/tinning
- Heat brazed joints to be opened with an autogenous flame. Lift off remaining metal and remove remaining brazing solder with a wire brush.
- Remove the paint and zinc coating in an area of approx. 30 mm around the seam to be soldered.
- Remove the paint and zinc coating in the tin-plating area and approx. 30 mm beyond.
- Brazing/tinning
- Execute brazed seam without overheating the solder and with low heat dissipation. If necessary, use heat protecting paste.
- Subsequent treatment of brazed joints:
- Remove burnt residual zinc completely. Straighten, grind and tin visible connection points.
- Remove burnt paint with a stainless steel wire brush.
- General information
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.