Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2011M3 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2125 (BRAKES - TIGHTENING TORQUES)SLIP CONTROL SYSTEM (DSC)34 51 SLIP CONTROL SYSTEM (DSC)
2011 BMW M3 2D Coupe, Standard
34 51 Slip Control System (DSC)
2011 BMW M3 2D Coupe, StandardSECTION 34 51 Slip Control System (DSC)
WARNING: This page does not describe the selected car, but rather 50 other vehicles, including the 2016 BMW M5, 2016 BMW ActiveHybrid 5, 2016 BMW 550i xDrive, 2016 BMW 550i, and 2016 BMW 535i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - SLIP CONTROL SYSTEM (DSC)
| Type | Thread | Tightening specifications | Value | ||
|---|---|---|---|---|---|
| 1AZ | Control unit to hydraulic control unit | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | Initial torque | 2±0.5 Nm | |
| Final torque | 4.3+0.5 Nm | ||||
| 2AZ | ICM control unit to body | F01/F02/F03/F06/F07/F07/F10/F11/F12/F18/F13/F25/F26 | Replace screws. | 8 Nm | |
| 3AZ | Pulse sensor to swivel bearing/wheel carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18/F25/F26 | M6x16 | 8 Nm | |
| Pulse sensor to swivel bearing, front, all-wheel drive vehicles | F01, F02, F04, F06, F07, F10, F11, F12 | M6x16 | Hexagon screw AF 10 Replace screw |
12 Nm | |
| 4AZ | Hydraulic control unit to holder | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18/F25/F26 | M8 | 8 Nm | |
| 5AZ | Holder, hydraulic control unit, to body | F01/F02/F03/F04/F06/F07/F10/F12/F13/F11/F18 | 19 Nm | ||
| F25/F26 | M6 | 8 Nm | |||
| 6AZ | Pulse sensor adapter to swivel bearing | F03 | M6 | 8 Nm | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.