Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2011750LI BASE, 4.4 CREPAIR AND DIAGNOSISSUSPENSIONELECTRONIC SUSPENSIONINTEGRATED SUSPENSION SYSTEMS - REPAIR - F01/F02
2011 BMW 750Li Base, 4.4 C
Integrated Suspension Systems - Repair - F01/F02
2011 BMW 750Li Base, 4.4 CSECTION Integrated Suspension Systems - Repair - F01/F02
- Safety Information
- General Information
- 37 10 001 Initial operation with test run of Dynamic Drive
- 37 10 001 Start-up with test run of Dynamic Drive (EPS steering gear)
- 37.... Overview of Dynamic Drive (ARS)
- 37 13... Overview of Dynamic Drive (ARS) pressure lines, front axle
- 37 13... Overview of Dynamic Drive (ARS) pressure lines, rear axle
- 37.... Overview of Vertical Dynamics Management (VDM)
- 37 13... Overview of lines, steering with ARS
- 37...... Overview of ride-height control system
- 37 00... Checking air springs for damage
- 37 00... Notes on air spring system
- 37 00.. Notes in the event of vehicle inclination
- 37..... Performing vertical acceleration sensor adjustment (vertical dynamics management)
- Front Control And Suspension Elements
- 37 11 030 Removing and installing front left or right spring strut
- 31 33 100 Replacing front left or right coil spring
- 37 11 010 Removing and installing/replacing front active anti-roll bar
- 37 11 032 Replacing front left or right spring strut shock absorber
- 37 11 020 Replacing pressure relief valves for active anti-roll bar at front
- Rear Control And Suspension Elements
- 37 12 012 Carrying out ride height adjustment
- 37 00... Checking air springs for damage
- 37 12 070 Removing and installing/replacing rear left or right air spring strut
- 37 12 1090 Removing and installing rear left or right spring strut
- 37 12 092 Replacing rear left or right spring strut
- 37 12 220 Removing and installing/replacing rear active anti-roll bar
- 37 12... Replacing pipes for air springs
- 37 12... Replacing ventilation line for air supply unit
- Connecting Lines
- 37 13... Overview of Dynamic Drive (ARS) pressure lines, front axle
- 37 13... Overview of Dynamic Drive (ARS) pressure lines, rear axle
- 37 13... Overview of lines, steering with ARS
- 37 13... Notes on fitting a new pipe or a screw connection
- 32 41... Removing/installing/replacing Dynamic Drive/ARS/power steering hoses and lines
- 37 13 120 Removing and installing/replacing pressure line for VA1 swivel motor
- 37 13 127 Removing and installing/replacing pressure lines for valve block (short)
- 37 13 121 Removing and installing/replacing pressure line for valve block VA1
- 37 13 126 Removing and installing/replacing pressure line for valve block VA2
- 37 13 132 Removing and installing/replacing pressure lines for oscillating motor (HA1/HA2)
- 37 13 130 Removing and installing/replacing underfloor pressure lines for oscillating motor (HA1/HA2)
- 37 13 125 Removing and refitting/replacing pressure line on swivel motor VA2
- 37 13... Replacing return line (short)
- Electrical Components
- 37 14 055 Removing and installing/replacing Vertical Dynamics Management control unit (VDM with Dynamic Drive)
- 37 14 525 Removing and installing/replacing control unit for air supply system
- 37 14 515 Replacing front left or right ride-height sensor
- 37 14 515 Replacing rear left or right ride height sensor
- Pump Assembly With Container
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.