Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2009X3 STANDARDREPAIR AND DIAGNOSISBODY & FRAMESEATSSEATS - TIGHTENING TORQUES10 FRONT SEATS52 10 FRONT SEATS
2009 BMW X3 Standard
52 10 Front Seats
2009 BMW X3 StandardSECTION 52 10 Front Seats
FRONT SEATS - TIGHTENING TORQUES
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Seat to floor plate | E31 / E32 / E34 / E36 | M10 | 44 Nm | |
| E36 / Z3 front | M8 | 22 Nm | ||
| E36 / Z3 rear | M10 | 43 Nm | ||
| E38 / E39 / E46 / E52 / E53 / E63 / E64 / E83 / E85 | M10 | 45 Nm | ||
| Torque angle | 90° | |||
| E60 / E61 / E65 / E66 / E67 / E87 / E90 / E91 | M10 (trilobular) | Replace Powerlok screw | 44 Nm | |
| 2AZ Backrest frame to seat frame | E36 | 60 Nm | ||
| E63 / E64 / E83 / E85 | 32 Nm | |||
| E46 all except Convertible | Replace screws | 32 Nm | ||
| E65 / E66 / E67 / E60 / E61 | M10 (trilobular) | Replace Powerlok screw | 33 Nm | |
| E53 | 45 Nm | |||
| 3AZ Support (backrest shell) to headrest rail | E31 | 6.5 Nm | ||
| 4AZ Head restraint rail to backrest frame | E31 | 25 Nm | ||
| 5AZ Finisher on seat rail | E38 / E39 | M4 | 4 Nm | |
| 6AZ Seat frame to seat runner | E38 / E39 | M6 | 15 Nm | |
| E60 / E61 / E65 / E66 | M8 | 27 Nm | ||
| 7AZ Actuating unit to seat frame | E46 / E85 | 10±2 Nm | ||
| 8AZ Adjusting screw for eccentric element | E46 / E85 | 1.4 Nm | ||
| 9AZ Seat pan to seat frame | E46 / E53 / E63 / E64 / E83 / E85 | 10±2 Nm | ||
| 10AZ Microswitch to front seat | E46 | 2±1 Nm | ||
| 11AZ Backrest frame to seat rail | E31 | 25 Nm | ||
| 12AZ Trims to seat mechanism | E63 / E64 | 3 Nm | ||
| 13AZ Trim to seat cushion shell | E63 / E64 | 4.4 Nm | ||
| 14AZ Backrest frame to seat frame - Screw | E46 Convertible | Replace screws | 24 ±4 Nm | |
| 15AZ Backrest frame to seat frame - Pin with knurling and lock nut | E46 Convertible | Replace screws | 40 ±5 Nm | |
| 16AZ Seat tilt adjuster to seat mechanism | E46 / E53 / E83 / E85 | M6 x 10 (trilobular) | Replace Taptite screw | 9 Nm |
| 17AZ Seat tilt adjuster to seat pan | E46 / E53 / E83 / E85 | 9 Nm | ||
| 18AZ Active head restraint Sliding rails with gas cartridge | E60 / E61 / E65 / E66 / E67 | 8 Nm | ||
| 19AZ Belt guide to backrest | E85 | 1.25 Nm | ||
| 20AZ Kinematic element to backrest frame | E46 Convertible | 3 +2 Nm |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.