SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2007530XI 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2209 (MAINTENANCE AND GENERAL INFORMATION - SPECIAL TOOLS)MAINTENANCE AND GENERAL DATA00 9 310 ASSEMBLY WEDGES (SET IN PLASTIC CASE)
2007 BMW 530xi 4D Sedan, Standard

00 9 310 Assembly wedges (set in plastic case)

2007 BMW 530xi 4D Sedan, StandardSECTION 00 9 310 Assembly wedges (set in plastic case)
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2014 BMW X6, 2013 BMW X6, 2012 BMW X6, 2011 BMW X6, and 2010 BMW X6. However, it is still accessible from the selected car via links, so may be relevant.

Minimum set: Mechanical tools 

NOTE: For straightening and assembly jobs on vehicle bodies, e.g. fitting trim panels, removing window weatherstrips, repairing small-scale dents, removing residual adhesive materials, measuring gap widths, levering out trim panel parts

Series: E12, E21, E23, E24, E28, E30, E30/C, E30tou, E31, E32, E32/3, E34, E34tou, E36, E36/2, E36/3, E36/5, E36/7, E36/C, E36tou, E38, E38/3, E39, E39PL, E39tou, E46, E46/16, E46/2, E46/3, E46/5, E46/C, E52, E53, E60, E61, E63, E64, E65, E66, E67, E68, E70, E71, E81, E82, E83, E85, E86, E87, E88, E90, E91, E92, E93, F01, F02, R50, R52, R53, R55, R56, RR1, RR2, RR3

Fig 1: Identifying Special Tool (00 9 310)
G04739103Courtesy of BMW OF NORTH AMERICA, INC.

SI number: 1 25 05 230

Order number: 00 9 310

Assembly wedges (set in plastic case)

Consisting of:

1 = 00 9 311 Trim remover

2 = 00 9 312 Striking wedge, square

3 = 00 9 313 Striking wedge, large

4 = 00 9 314 Adjustment wedges (2 x)

5 = 00 9 315 Gap wedge

6 = 00 9 316 Sealing lip wedge

9 = 00 9 319 Striking wedge, small

10= 00 9 321 Fishbone

11= 00 9 322 Plastic wedge

13= 00 9 324 Trim remover (sheet)

NOTE: For removing shaft strips from E60

14= 00 9 329 Case with insert for mounting wedges

In conjunction with: 009310

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.