Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW1987L7 (E23) L6-3430CC 3.4L SOHC (M30)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSUPDATED MODIC(R) SOFTWARE - C9.0 ZCS CODINGOVERVIEW
1987 BMW L7 (E23) L6-3430cc 3.4L SOHC (M30)
Updated MoDic(R) Software - C9.0 ZCS Coding: Overview
1987 BMW L7 (E23) L6-3430cc 3.4L SOHC (M30)SECTION Overview
Group O8
MODIC
Bulletin Number
08 03 96
Woodcliff Lake, NJ
February 1997
Product Engineering
This IDC bulletin supersedes IDC 08 O3 96 dated September 1996 which should be removed and discarded from your IDC binder.
SUBJECT:
Updated MODIC Software C9.0 ZCS Coding
MODEL:
ALL
Situation:
A revised and expanded version of the MODIC ZCS coding Software has been developed. With the release of C9.0 MODIC Software, Version C8.0 ZCS Encoding Software has become invalid.
Program Highlights
^ Updated information for all models.
^ Only codeable control modules (on the vehicle in question) are displayed on the MODIC screen. The Central Coding Key determines which control modules are codeable.
^ Central Coding Key - The E39 and the Z3 use a 37 digit instead of a 48 digit Central Coding Key. If the Central Coding Key is altered (via conversion), write the new Central Coding Key on a label. Affix the label to the appropriate vehicle Central Coding Key sticker location. Place the new label next to the old label. Cross out the old label. Label location -
E39 - In the right side of the trunk next to the fusible link
Z3 - On the bottom side of the E-Box lid
^ After replacement the following control modules require coding with C9.0. When coding is complete check the control module's fault memory and erase any faults present.
Overview of Conversions
Footnote: # = It is only possible to enhance the blower on the IHKA from software 37 that was introduced approximately 9/95.
Menu Access
Select Series
Select "4" conversion
Select system (example IHKA)
Select Function (example "1" temperature C/F)
Select "Y" to start automatic coding
Overview of Retrofits
E36
5-Onboard Computer E36/5 - must be encoded within 36 hours of
installation.
6-Cruise Control From 9/94 production
Menu Access:
Select Series
Select "2" Retrofitting
Select System (example "1" IHKA)
Select "Y" to start automatic encoding
Parts Information
Software Version C9.0 A/B
P/N 01 11 9 788 251
introductory Price = $49.00
Return any defective diskettes to BMW NA via the BMW Tool Warranty. Details of the program can be found in your Parts information Binder under bulletin 1-24 dated 4/95.
Additional copies may be purchased through your Parts Distribution Center.
MODIC
Bulletin Number
08 03 96
Woodcliff Lake, NJ
February 1997
Product Engineering
This IDC bulletin supersedes IDC 08 O3 96 dated September 1996 which should be removed and discarded from your IDC binder.
SUBJECT:
Updated MODIC Software C9.0 ZCS Coding
MODEL:
ALL
Situation:
A revised and expanded version of the MODIC ZCS coding Software has been developed. With the release of C9.0 MODIC Software, Version C8.0 ZCS Encoding Software has become invalid.
Program Highlights
^ Updated information for all models.
^ Only codeable control modules (on the vehicle in question) are displayed on the MODIC screen. The Central Coding Key determines which control modules are codeable.
^ Central Coding Key - The E39 and the Z3 use a 37 digit instead of a 48 digit Central Coding Key. If the Central Coding Key is altered (via conversion), write the new Central Coding Key on a label. Affix the label to the appropriate vehicle Central Coding Key sticker location. Place the new label next to the old label. Cross out the old label. Label location -
E39 - In the right side of the trunk next to the fusible link
Z3 - On the bottom side of the E-Box lid
^ After replacement the following control modules require coding with C9.0. When coding is complete check the control module's fault memory and erase any faults present.
Overview of Conversions
Footnote: # = It is only possible to enhance the blower on the IHKA from software 37 that was introduced approximately 9/95.
Menu Access
Select Series
Select "4" conversion
Select system (example IHKA)
Select Function (example "1" temperature C/F)
Select "Y" to start automatic coding
Overview of Retrofits
E36
5-Onboard Computer E36/5 - must be encoded within 36 hours of
installation.
6-Cruise Control From 9/94 production
Menu Access:
Select Series
Select "2" Retrofitting
Select System (example "1" IHKA)
Select "Y" to start automatic encoding
Parts Information
Software Version C9.0 A/B
P/N 01 11 9 788 251
introductory Price = $49.00
Return any defective diskettes to BMW NA via the BMW Tool Warranty. Details of the program can be found in your Parts information Binder under bulletin 1-24 dated 4/95.
Additional copies may be purchased through your Parts Distribution Center.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.