Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Component Location Overview - Sound System, Sedan
2024 Audi S3 PremiumSECTION Component Location Overview - Sound System, Sedan
- Left Front Midrange Speaker -R103-
- Only for 9VS
- Removing and Installing. Refer to FRONT MIDRANGE SPEAKER, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Center Speaker 2 -R219-
- Only for 9VS
- Removing and Installing. Refer to Center Speaker 2 -R219-, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Center Speaker -R208-
- Only for 9VD/9VS
- Removing and Installing. Refer to Center Speaker -R208-, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Right Front Midrange Speaker -R104-
- Only for 9VS
- Removing and Installing. Refer to FRONT MIDRANGE SPEAKER, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Right Front Treble Speaker -R22-
- Removing and Installing. Refer to Left Front Treble Speaker -R20- /Right Front Treble Speaker -R22-, REMOVING AND INSTALLING .
- Interior Microphone -R74-
- Only for 9VS
- In the Front Roof Module -WX3-
- Overview. Refer to OVERVIEW - MICROPHONE UNIT .
- Removing and Installing. Refer to Interior Microphone -R74-, REMOVING AND INSTALLING .
- Front Roof Module -WX3-
- Removing and installing. Refer to FRONT INTERIOR LAMP/READING LAMP, REMOVING AND INSTALLING .
- Right Rear Bass Speaker -R17-
- Removing and Installing. Refer to Left Rear Bass Speaker -R15- /Right Rear Bass Speaker -R17-, REMOVING AND INSTALLING .
- Bolt tightening specification: 4 Nm
- Right Rear Treble Speaker -R16-
- Only for 9VD/9VS
- Removing and Installing. Refer to Left Rear Treble Speaker -R14- /Right Rear Treble Speaker -R16-, REMOVING AND INSTALLING .
- Left Effects Speaker -R209-
- Only for 9VS
- Removing and Installing. Refer to EFFECTS SPEAKER, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Right Effects Speaker -R210-
- Only for 9VS
- Removing and Installing. Refer to EFFECTS SPEAKER, REMOVING AND INSTALLING .
- Bolt tightening specification: 1.5 Nm
- Digital Sound System Control Module -J525-
- Only for 9VS
- Removing and Installing. Refer to CONTROL MODULE/DIGITAL SOUND SYSTEM AMPLIFIER, REMOVING AND INSTALLING, SEDAN .
- Subwoofer -R211-
- Only for 9VD/9VS
- Removing and Installing. Refer to Subwoofer -R211-, REMOVING AND INSTALLING .
- Bolt tightening specification: 4.5 Nm
- Nut tightening specification: 6 Nm
- Left Rear Treble Speaker -R14-
- Only for 9VD/9VS
- Removing and Installing. Refer to Left Rear Treble Speaker -R14- /Right Rear Treble Speaker -R16-, REMOVING AND INSTALLING .
- Left Rear Bass Speaker -R15-
- Removing and Installing. Refer to Left Rear Bass Speaker -R15- /Right Rear Bass Speaker -R17-, REMOVING AND INSTALLING .
- Bolt tightening specification: 4 Nm
- Right Front Bass Speaker -R23-
- Removing and Installing. Refer to Left Front Bass Speaker -R21- /Right Front Bass Speaker -R23-, REMOVING AND INSTALLING .
- Bolt tightening specification: 4 Nm
- Left Front Bass Speaker -R21-
- Removing and Installing. Refer to Left Front Bass Speaker -R21- /Right Front Bass Speaker -R23-, REMOVING AND INSTALLING .
- Bolt tightening specification: 4 Nm
- Left Front Treble Speaker -R20-
- Removing and Installing. Refer to Left Front Treble Speaker -R20- /Right Front Treble Speaker -R22-, REMOVING AND INSTALLING .
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.