Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2019S5 PRESTIGE, 2D COUPEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 141 (CONVERTIBLE TOP)
2019 Audi S5 Prestige, 2D Coupe
Section 141 (Convertible Top)
2019 Audi S5 Prestige, 2D CoupeSECTION Section 141 (Convertible Top)
WARNING: This page is about a different car, the 2019 Audi A5 Sportback and 2018 Audi A5 Sportback. However, it is still accessible from the selected car via links, so may be relevant.
- 61 Convertible Top
- Convertible Top
- Overview - Convertible Top
- Overview - Convertible Top Frame
- Overview - Convertible Top Main Bearing
- Overview - Convertible Top Latch
- Convertible Top, Removing And Installing
- Convertible Top Retaining Plate, Removing And Installing
- Convertible Top Latch, Removing And Installing
- Convertible Top End Panel, Removing And Installing
- MOUNT WITH Convertible Top Locking Motor -V223-, REMOVING AND INSTALLING
- Convertible Top And Convertible Top Compartment Cover Service Position
- Emergency Operation
- Convertible Top Cover
- Overview - Convertible Top Cover And Convertible Top Headliner
- Overview - Convertible Top Cover Tension And Guide Cable
- Overview - Convertible Top Headliner Tension And Guide Cable
- Overview - Repair Kit Tension And Guide Cable
- Convertible Top Cover, Removing And Installing
- Convertible Top Headliner, Removing And Installing
- Convertible Top Cover Tension Cable, Removing And Installing
- Rear Lid Relay Lever Tension Cable, Removing And Installing
- Tension And Guide Cables Procedure For Repair
- Attachments
- Overview - Convertible Top Seals
- Overview - Convertible Top Trim Panels
- Overview - Convertible Top Frame Attachments
- Convertible Top Seals, Removing And Installing
- Convertible Top Trim Panels, Removing And Installing
- Connecting Rod, Removing And Installing
- Shock Absorber, Removing And Installing
- Rear Interior Lamp Mount, Removing And Installing
- Rear Window Relay Lever, Removing And Installing
- Hydraulic System
- Component Location Overview - Hydraulic System
- Overview - Hydraulic System
- Overview - Hydraulic Pump
- Hydraulic Pump, Removing And Installing
- Hydraulic Pump With Hydraulic Cylinders, Removing And Installing
- Hydraulic Pump Motor, Removing And Installing
- Hydraulic Cylinder, Removing And Installing
- Hydraulic Line, Removing And Installing
- Hydraulic System Fluid Level, Checking
- Hydraulic System, Filling And Bleeding
- Electrical And Electronic Components
- Component Location Overview - Electric And Electronic Components
- Convertible Top Control Module -J256-, REMOVING AND INSTALLING
- Convertible Top Latch -Open- Switch -F294- /Convertible Top Latch -Closed- Switch -F295-, REMOVING AND INSTALLING
- Convertible Top Stowed Position Switch -F171- /Convertible Top Front Closed Position Switch -F202-, REMOVING AND INSTALLING
- Upper Tensioning Bow Switch - F408- /Left Tensioning Bow Lowered Position Switch -F419-, REMOVING AND INSTALLING
- Intermediate Position Bracket Switch -F518- /Right Tensioning Bow Lowered Position Switch -F420-, REMOVING AND INSTALLING
- Convertible Top Compartment -Open- Switch -F407-, REMOVING AND INSTALLING
- Rear Passenger Compartment Monitoring Left And Right Ultrasound Sensor -G981- And -G982-, Removing And Installing
- Special Tools
- Convertible Top
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.