Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2018A5 QUATTRO PRESTIGE, 2D CONVERTIBLEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 251 (CONTROLS, HOUSING (1 OF 2))34 CONTROLS, HOUSINGSELECTOR MECHANISMOVERVIEW - SELECTOR MECHANISM
2018 Audi A5 Quattro Prestige, 2D Convertible
Overview - Selector Mechanism
2018 Audi A5 Quattro Prestige, 2D ConvertibleSECTION Overview - Selector Mechanism
WARNING: This page is about a different car, the 2022 Audi A4 allroad, 2021 Audi A4 allroad, and 2020 Audi A4 allroad. However, it is still accessible from the selected car via links, so may be relevant.
Selector Mechanism in the Vehicle Interior
- Selector Mechanism
- With the following integrated components:
- Selector Lever -E313-
- Selector Lever Position Sensor -G727-
- Transverse Selector Lever Lock Sensor -G868-
- Selector Lever Sensor System Control Module -J587-
- Shift Lock Solenoid -N110-
- Transverse Selector Lever Lock Motor -V577-
- The components cannot be replaced separately if faulty.
- Removing and installing. Refer to SELECTOR MECHANISM, REMOVING AND INSTALLING .
- With the following integrated components:
- Selector Lever Transmission Range Display -Y5-
- Removing and installing. Refer to COMPONENT LOCATION OVERVIEW - CENTER CONSOLE LAMPS .
- Selector Lever Handle, Upper Section
- Removing and installing. Refer to SELECTOR LEVER HANDLE, REMOVING AND INSTALLING .
- Bolt
- 3.2 Nm
- Not available separately
- Selector Lever Handle, Lower Section
- With the following integrated components:
- Selector Lever Release Button -E681-
- Parking Lock Button -E816-
- The components cannot be replaced separately if faulty.
- Removing and installing. Refer to SELECTOR LEVER HANDLE, REMOVING AND INSTALLING .
- With the following integrated components:
- Selector Lever Boot
- Removing and installing. Refer to SELECTOR LEVER BOOT ON SELECTOR LEVER HANDLE, DISCONNECTING AND ASSEMBLING .
- Bolt
- 8 Nm
Gearshift Mechanism on Transmission
- Drive Position Sensor -G676-
- Removing and installing. Refer to Parking Lock Solenoid -N486- /Drive Position Sensor -G676-, REMOVING AND INSTALLING .
- Shaft
- For the parking lock
- Bolt
- 3 Nm + 90°
- Always replace after removing
- M6 X 30
- Parking Lock Solenoid -N486-
- Electro-hydraulic part
- Removing and installing. Refer to Parking Lock Solenoid -N486- /Drive Position Sensor -G676-, REMOVING AND INSTALLING .
- Seal
- Always replace after removing
- Seal
- Replacing. Refer to PARKING LOCK SHAFT SEAL, REPLACING .
- For the parking lock shaft
- Spring Pin
- Lever
- For the parking lock
- Removing and installing. Refer to PARKING LOCK SHAFT SEAL, REPLACING .
- Cover
- For the parking lock
- With electric wiring harness
- Bolt
- 3 Nm + 45°
- Always replace after removing
- M6 X 14
- Bolt
- 8 Nm + 60°
- Always replace after removing
- M8 X 22
- Alignment Pin
- Quantity: 2
- Bolt
- 3 Nm + 180°
- Always replace after removing
- M6 X 55
- Bolt
- 3 Nm + 90°
- Always replace after removing
- M6 X 35
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.