Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2018A5 QUATTRO PRESTIGE, 2D CONVERTIBLEREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESCOMMON SPECIFICATIONS & PROCEDURES (CONVERTIBLE)SPECIFICATIONS INDEX
2018 Audi A5 Quattro Prestige, 2D Convertible
Specifications Index
2018 Audi A5 Quattro Prestige, 2D ConvertibleSECTION Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | R1234yf WORKING WITH A/C SERVICE STATION (1 OF 2) and WORKING WITH A/C SERVICE STATION (2 OF 2) R134a 87 AIR CONDITIONING (1 OF 2) and 87 AIR CONDITIONING (2 OF 2) |
||
| Torque | OVERVIEW - A/C COMPRESSOR POWER UNIT | ||
| Axle Nut/Hub Nut | |||
| Front | 200 Nm +180° | ||
| Rear | 200 Nm +180° | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC SYSTEM, BLEEDING |
||
| Disc Brakes | TECHNICAL DATA, BRAKES | ||
| Torque | OVERVIEW - FRONT BRAKES OVERVIEW - REAR BRAKES |
||
| Charging | |||
| Generator | N/A | ||
| Torque | |||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT, REMOVING AND INSTALLING | ||
| Belt Routing | |||
| 2.0L | Vehicles with Generator, See fig. 2 under OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE, VEHICLES WITH GENERATOR Vehicles with Starter Generator, See fig 5 under OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE, VEHICLES WITH STARTER GENERATOR |
||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | COOLING SYSTEM, CHECKING FOR LEAKS | ||
| Thermostat R & I | |||
| 2.0L | OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | COOLANT PUMP, REMOVING AND INSTALLING | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION, CHECKING | ||
| Oil Pressure | OIL PRESSURE, CHECKING | ||
| Overhaul | 10 ENGINE ASSEMBLY 13 CRANKSHAFT, CYLINDER BLOCK 15 CYLINDER HEAD, VALVETRAIN |
||
| Torque | Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Engine Oil Drain Plug | 30Nm | ||
| Flywheel/Flex Plate Torque | 60 Nm + 90° turn | ||
| Fuel System | |||
| Fuel Pressure Test Procedure | |||
| 2.0L | TRANSFER FUEL PUMP -G6-, CHECKING | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L | SPARK PLUGS, REPLACING | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | OVERVIEW - STARTER | ||
| Wheel Alignment | |||
| Adjustment Specifications | AXLE ALIGNMENT | ||
| Torque | Refer to the appropriate procedure in: 40 FRONT SUSPENSION 42 REAR SUSPENSION |
||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Standard Wheel 89 Ft. Lbs (120 Nm) PAX Wheel 103 Ft. Lbs (140 Nm) |
||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.