SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2009A6 BASEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 23 (4.2L - GENERIC SCAN TOOL, ENGINE CODE(S): BVJ (ST-GENERIC SCAN TOOL))ST - GENERIC SCAN TOOLDIAGNOSTIC TROUBLE CODE TABLESSAE P0XXX DTCSCONTROL MODULE AND OUTPUT SIGNALS
2009 Audi A6 Base

Control module and output signals

2009 Audi A6 BaseSECTION Control module and output signals
WARNING: This page is about a different variant/trim than selected.
DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illum
P0601 Internal Control Module Memory Check Sum Error Internal check sum, incorrect   0.5 Seconds
  • Continuous
  • 2 DCY
P0602 Control Module Programming Error Reprogramming not completed   0.5 Seconds
  • Continuous
  • 2 DCY
P0604 Internal Control Module Random Access Memory (RAM) Error Write ability check, failed   0.5 Seconds
  • Continuous
  • 2 DCY
P0606 ECM/PCM Processor
  • Sensor offset correction >0.1 V
  • Sensor IC power supply voltage 9 V
  • Communication CPU sensor IC Failed
  • Delta resistance measured vs. modeled >15 Ohm
  • Signal voltage 0.2 V
  • Signal voltage >4.88 V
  • Drive by wire module check failed
  • EEPROM check failed
  • Engine torque out of range
  • Engine operation condition out of range
  • Engine speed, Idle >2 Sec.
  • Engine speed, >25 RPM
 10 Seconds 0.2 Seconds 0.5 Seconds
  • Continuous
  • 2 DCY
P0613 TCM Processor Check-calculation of 1st CPU failed, Single reset does not cover problem      
P0614 ECM/TCM Incompatible Detection of error signal
  • CAN bus, Active
  • ECU communication, Active
  • ECU data update, Active
 250 ms  
P062B Injector Valves Communication CPU   Engine speed, >80 RPM 2 Seconds
  • Continuous
  • 2 DCY
P0638 Throttle Actuator Control Range/Performance - Bank 1
  • Time to open over reference point + 12%, > 0.14 Sec.
  • Time to close below reference point, + 3%, > 0.56 Sec.
  • Time to close below reference point + 1%, > 0.14 Sec.
  • Time to close over reference point, -1.5%, > 0.56 Sec.
  • TPS 1 signal voltage, 0.21 V or 0.87 V
  • TPS 2 signal voltage, 4.14 V or 4.84 V
  • Ignition, On
  • Engine speed, 0 RPM
  • IAT, >5° C
  • Vehicle speed, 0 MPH
  • ECT, >5° C
 5 Seconds
  • Continuous
  • 2 DCY
P0641 Sensor Reference Voltage A Circuit/Open Internal Fault   0.4 Seconds
  • Continuous
  • 2 DCY
P0642 Sensor Reference Voltage A Circuit Low Signal voltage, 4.606-4.998 V   0.4 Seconds
  • Continuous
  • 2 DCY
P0643 Sensor Reference Voltage A Circuit High Signal voltage, >4.998-5.406 V   0.4 Seconds
  • Continuous
  • 2 DCY
P0651 Sensor Reference Voltage B Circuit/Open Internal Fault   0.4 Seconds
  • Continuous
  • 2 DCY
P0652 Sensor Reference Voltage B Circuit Low Signal voltage, 4.606-4.998 V   0.4 Seconds
  • Continuous
  • 2 DCY
P0653 Sensor Reference Voltage B Circuit High Signal voltage, >4.998-5.406 V   0.4 Seconds
  • Continuous
  • 2 DCY
P0657 Actuator Supply Voltage A Circuit/Open Signal voltage, > 4.4-5.6 V
  • Relay, Commanded off
  • Engine speed, > 40 RPM
 0.5 Seconds
  • Continuous
  • 2 DCY
P0658 Actuator Supply Voltage A Circuit Low Signal voltage, 2.15-3.25 V
  • Relay, Commanded off
  • Engine speed, > 40 RPM
 0.5 Seconds
  • Continuous
  • 2 DCY
P0659 Actuator Supply Voltage "A" Circuit High Signal current >1.1 A
  • Relay, Commanded on
  • Engine speed, > 40 RPM
 0.5 Seconds
  • Continuous
  • 2 DCY
P0685 ECM/PCM Power Relay Control Circuit/Open
  • Signal voltage, 2.6-3.7 V
  • Sense circuit voltage, 6 V
  • Main relay, Commanded on
  • ECM keep alive time
 0.5 Seconds
  • Continuous
  • 2 DCY
P0686 ECM/PCM Power Relay Control Circuit Low
  • Signal voltage, 2.6-3.7 V
  • Sense circuit voltage, 6 V
  • Main relay, Commanded on
  • ECM keep alive time
 0.5 Seconds
  • Continuous
  • 2 DCY
P0687 ECM/PCM Power Relay Control Circuit High
  • Signal current, >0.7-1.4 A
  • Sense circuit voltage, 6 V
  • Main relay, Commanded on
  • ECM keep alive time
 0.5 Seconds
  • Continuous
  • 2 DCY
P0688 ECM/PCM Power Relay Sense Circuit
  • Sense voltage, 4.0 V
  • Sense circuit voltage vs. on board voltage >1V
  • Sense circuit voltage >16 V
  • Sense circuit voltage vs. on board voltage >2.5 V
  • Main relay, Commanded on
  • ECM keep alive time
  • ECM keep alive time
  • Camshaft actuator, Commanded on
 1 Second 0.5 Seconds
  • Continuous
  • 2 DCY
P0697 Sensor Reference Voltage C Circuit/Open Internal Fault   0.4 Seconds
  • Continuous
  • 2 DCY
P0698 Sensor Reference Voltage C Circuit Low Signal voltage, 4.606-4.998 V   0.4 Seconds
  • Continuous
  • 2 DCY
P0699 Sensor Reference Voltage C Circuit High Signal voltage, >4.998-5.406 V   0.4 Seconds
  • Continuous
  • 2 DCY
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.