Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2007RS4 QUATTRO SEDAN (8EC) V8-4.2L (BNS)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONMODE 6 DATAPART 2
2007 Audi RS4 Quattro Sedan (8EC) V8-4.2L (BNS)
Part 2
2007 Audi RS4 Quattro Sedan (8EC) V8-4.2L (BNS)SECTION Part 2
Diagnostic Modes - (Continued)
Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 65 ($41)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 69 ($45): Oxygen Sensor Heater Monitor Bank 2- Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 69 ($45)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 73 ($49): Oxygen Sensor Heater Monitor Bank 3 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 73 ($49)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 77 ($4D): Oxygen Sensor Heater Monitor Bank 4 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 77 ($4D)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 66 ($42)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 70 ($46)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 74 ($4A): Oxygen Sensor Heater Monitor Bank 3 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 74 ($4A)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 78 ($4E): Oxygen Sensor Heater Monitor Bank 4 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 78 ($4E)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
OBDMID $71 (113): Secondary Air Injection (AIR) System 1 (Bank 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 71 ($113)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
OBDMID $72 (114): Secondary Air Injection (AIR) System 2 (Bank 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 72 ($114)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
OBDMID $73 (115): Secondary Air Injection (AIR) System 3 (Bank 3)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 71 ($113)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
OBDMID $74 (116): Secondary Air Injection (AIR) System 4 (Bank 4)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 74 ($116)".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 162 ($A2)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 163 ($A3): Mis-Fire Cylinder 2 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 163 ($A3)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 164 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 165 ($A5)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 166 ($A6): Mis-Fire Cylinder 5 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 166 ($A6)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 167 ($A7): Mis-Fire Cylinder 6 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 167 ($A7)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 168 ($A8): Mis-Fire Cylinder 7 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 168 ($A8)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
Test-ID 169 ($A9): Mis-Fire Cylinder 8 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 169 ($A9)".
- Select the desired "Test-ID (TID)" or "Hex-ID ".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.