Telephone/Telematics System

Telephone/Telematics System

=> [ Microphone Function Test ]

=> [ Telematics Service Mode, Activating/Deactivating ]

=> [ Telephone/Telematics Control Module, Initialization ]

Microphone Function Test

With Bose(R) sound, and Inside Microphone (R74 ) is installed to determine interior noise (AudioPilot). This is switched directly with the Amplifier (R12). If interior noise increases, the Amplifier (R12) automatically increases volume according to a predetermined pattern.

After switching on the Radio (R), the Amplifier (R12) determines the gauge of the Inside Microphone (R74) voltage supply. If the result is OK, there is no reaction.

In contrast, if no Inside Microphone (R74) is installed, three short tones sound one after another.

In case of short circuit, three individual tones are heard.

Function test

- Switch the Radio (R) on and set it to a station (pop music, if possible).

- Set the volume to approximately "20".

- Now lightly tap on the Inside Microphone (R74 ) (Front Interior Light (W1)) several times.

The volume of the station selected on the Radio ( R) must increase noticeably during the tapping. The procedure is done slowly.

- Stop tapping.

The volume of the station selected on the Radio ( R) must decrease noticeably.

Telematics Service Mode, Activating/Deactivating

CAUTION!
• Telephone, Telematics Control Module must be put in service mode before disconnecting battery.

• If this is not done, the Emergency Battery (Telematics) (A16) in Telephone/Telematics Control Module (J526) is discharged.

Service mode, activating

The Telematics is switched on.

- Press button sequence - #4610# - on the Telephone Handset (R37).

- Confirm entry by pressing Navi button on Telephone Handset (R37).

Shown on display:





Service mode is activated, Battery (A) can be disconnected.

Service mode, deactivating

The Battery (A) is connected.

Shown on display:





- Press the Navi button on the Telephone Handset (R37).

Service mode is deactivated.

Telephone/Telematics Control Module, Initialization

Initialization must be performed:

• at first usage, before delivery to customer

• after replacing vehicle bracket

• after replacing the Telematics SIM card

• after replacing the Telephone/Telematics Control Module (J526)

During initialization, there is an exchange of data between the Telephone/Telematics Control Module (J526) and the Telematics Service Center.

Before initializing, always wait for activation fax return message and Telematics SIM card must be activated.

Requirements

• sufficient D2 mobile phone network reception

• reception of at least 4 GPS satellites

• no 2nd cellular phone card in Telephone Handset ( R37)

Initialization process

- Switch Telephone Handset (R37) on.

Then the display:





- Press the Navi button until the display:





appears.

- Enter security code (always "12345") via number field and confirm entry with Navi button.

• Security code should be saved.

- Now enter Telematics call center number: "49 172 227 022 0 " and confirm entry with Navi button.

- Enter Telematics provider number: "2002" and confirm entry with Navi button.

Now the initialization of the Telephone/Telematics Control Module (J526) takes place (approximately 3 to 6 minutes).

Then the display:





- Confirm indicator with Navi button.

Then the display:





- Confirm indicator with Navi button.

Then the transmitted KFZ data can be compared with activation fax entries.

- Press arrow buttons to scroll through this menu.

Press C button to go to first menu level.

Initialization is ended.

In vehicles with RNS 4.1 and BNS 4.0 navigation systems, dynamic route guidance must be activated.

- Press Stau button.

- Under menu item "Always automatically avoid"

Selection: "ON"

press.

- Under menu item "Traffic information source"

Selection: "Telephone"

press.

- Under menu item "Traffic info inquiry frequency"

Selection: "Always periodically"

press.

Units are now ready for operation.