SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2005A6 3.2 TREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 16 (3.2L - GENERIC SCAN TOOL, ENGINE CODE: BKH)ST - GENERIC SCAN TOOLDIAGNOSTIC MODESDIAGNOSTIC MODE 06: CHECKING TEST RESULTS OF COMPONENTS THAT ARE NOT CONTINUOUSLY MONITOREDNOTES
2005 Audi A6 3.2 T

Diagnostic Mode 06: Checking Test Results of Components that are not Continuously Monitored: Notes

2005 Audi A6 3.2 TSECTION Notes
WARNING: This page is about a different car, the 2009 Audi A4, 2008 Audi A4, 2007 Audi A4, 2006 Audi A4, and 2005 Audi A4. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostic Mode 06 displays the test results of emission related components and systems which are not continuously monitored.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

NOTE:
  • Depending on diagnostic tester and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements 

  • Exhaust system must be properly sealed between catalytic converter and cylinder head.
  • No DTCs in the DTC memory.
  • Coolant temperature at least 80°C.

Work procedure 

  • Connect the diagnostic tester.
  • Start the engine and let run at idle speed.
  • Select "Mode 6: Check test the results of components that are not continuously monitored".

Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the diagnostic tester screen.

Test-ID (Hex-ID) Component or System
01 ($01): Test-ID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1  Oxygen Sensor Monitor Bank 1 - Sensor 1
02 ($02): Test-ID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2  Oxygen Sensor Monitor Bank 1 - Sensor 2
05 ($05): Test-ID 05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1  Oxygen Sensor Monitor Bank 2 - Sensor 1
06 ($06): Test-ID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2  Oxygen Sensor Monitor Bank 2 - Sensor 2
33 ($21): Test-ID 33 ($21): Catalyst Monitor Bank 1  Catalyst Monitor Bank 1
34 ($22): Test-ID 34 ($22): Catalyst Monitor Bank 2  Catalyst Monitor Bank 2
$3A (58): $3A (58): Fuel Tank EVAP System Leak Test (0.090)  Fuel Tank EVAP System Leak Test (0.090)
59 (3B): Test-ID 59 (3B): EVAP Monitor (0.040)  EVAP Monitor (0.40)
60 (3C): Test-ID 60 (3C): EVAP Monitor (0.020)  EVAP Monitor (0.20)
61 (3D): Test-ID 61 (3D): Purge Flow Monitor  Purge Flow Monitor
65 ($41): Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1  Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
66 ($42): Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2  Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
69 ($45): Test-ID 69 ($45): Oxygen Sensor Heater Monitor Bank 2 - Sensor 1  Oxygen Sensor Heater Monitor Bank 2 - Sensor 1
70 ($46): Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2  Oxygen Sensor Heater Monitor Bank 2 - Sensor 2
162 ($A2): Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data  Mis-Fire Cylinder 1 Data
163 ($A4): Test-ID 163 ($A4): Mis-Fire Cylinder 2 Data  Mis-Fire Cylinder 2 Data
164 ($A4): Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data  Mis-Fire Cylinder 3 Data
165 ($A5): Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data  Mis-Fire Cylinder 4 Data
166 ($A4): Test-ID 166 ($A4): Mis-Fire Cylinder 5 Data  Mis-Fire Cylinder 5 Data
167 ($A7): Test-ID 167 ($A7): Mis-Fire Cylinder 6 Data  Mis-Fire Cylinder 6 Data
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.