Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2004A4 BASE, 4D SEDAN, 3.0 TREPAIR AND DIAGNOSISELECTRICALGAUGESINTERIOR TRIM - CABRIOLET
2004 Audi A4 Base, 4D Sedan, 3.0 T
Interior Trim - Cabriolet
2004 Audi A4 Base, 4D Sedan, 3.0 TSECTION Interior Trim - Cabriolet
- Front door trims
- Component locations, assembly overview
- Door trim, assembly overview
- Trim, removing and installing
- Insulation, assembly overview
- Routing of wiring in door trim, assembly overview
- Armrest, removing and installing
- Central locking switch, removing and installing
- Mirror adjustment switch, removing and installing
- Interior door handle, removing and installing
- Switch panel for window regulator, removing and installing
- Switch panel for memory seat, removing and installing
- Switch panel for tailgate release and/or deactivation of anti-theft alarm, assembly overview
- Door warning light and courtesy light, removing and installing
- Treble loudspeaker, removing and installing
- Trim of bass loudspeaker, removing and installing
- Rear side trim
- Instrument panel
- Component locations, assembly overview
- Instrument panel, removing and installing
- Special tools and equipment
- Removing
- Remove left instrument panel cover
- Removing left instrument panel end mounting
- Detaching connectors on vent temperature sensor -G150- and -G151-
- Removing instrument panel vent
- Removing left and right instrument panel loudspeaker
- Removing and installing tray, switch and cup holder
- Removing light switch and adjuster for headlight range control
- Removing left instrument panel trim
- Removing instrument panel mountings driver's side.
- Removing upper steering column switch trim
- Removing sunlight penetration photosensor -G107-
- Removing trim for center defroster vent
- Removing center instrument panel loudspeaker
- Removing trim for right instrument panel cover.
- Removing right instrument panel cover
- Removing right instrument panel end mountings.
- Removing center instrument panel mountings
- Installing
- Left and/or right instrument panel air duct, removing and installing
- Central tube
- Trims
- Upper A-pillar trim, assembly overview
- Lower A-pillar trim, assembly overview
- Floor covering, assembly overview
- Sill panel trim, removing and installing
- Foot rest, removing and installing
- Foot rest holder, removing and installing
- Sun visor, removing and installing
- Sun visor mount, removing and installing
- Center sun visor, removing and installing
- Windshield trim, assembly overview
- Make-up mirror light, removing and installing
- Interior light / reading light, removing and installing
- Luggage compartment trim
- Trim for convertible top compartment
- Variable convertible top compartment
- Variable convertible top compartment, removing and installing
- Convertible top compartment lid, assembly overview
- Handle mount trim, assembly overview
- Handle for variable convertible top compartment, removing and installing
- Microswitch for variable convertible top compartment, removing and installing
- Toothed segment of variable convertible top compartment, removing and installing
- Rack of variable convertible top compartment, removing and installing
- Guide rail of variable convertible top compartment, removing and installing
- Console of variable convertible top compartment, assembly overview
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.