Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSAUDI1999A8 QUATTROREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 72 (ON BOARD DIAGNOSTIC (OBD) - RADIO, NAVIGATION, STEERING & TELEMATICS)TELEMATICS, ON BOARD DIAGNOSTIC (OBD)CODE CONTROL MODULE (FUNCTION 07)CODE CONTROL MODULE, INITIATING

1999 Audi A8 Quattro

Code Control Module, initiating

1999 Audi A8 QuattroSECTION Code Control Module, initiating

WARNING: This page does not describe the selected car, but rather 15 other vehicles, including the 2005 Audi allroad, 2004 Audi allroad, 2004 Audi A6, 2003 Audi allroad, and 2003 Audi S6. However, it is still accessible from the selected car via links, so may be relevant.

Indicated on display:

Fig 1: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (1 Of 7)

Courtesy of AUDI OF AMERICA, INC.

Press buttons -0- and -7- to select "Code control module" function 07.

Indicated on display:

Fig 2: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (2 Of 7)

Courtesy of AUDI OF AMERICA, INC.

Press -Q- button to confirm input.

Indicated on display:

Fig 3: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (3 Of 7)

Courtesy of AUDI OF AMERICA, INC.

Enter seven digit code number according to table. See CODING TABLE: .
Press -Q- button to confirm input.

Coding example: 0002333

000: = not used: always 000 (reserved)
2 = Vehicle model: A6
3 = Multi-function steering wheel & voice recognition
3 = Navigation system IV
3 = Radio system: Symphony/BOSE

Indicated on display (control module identification and coding entered)

Fig 4: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (4 Of 7)
Courtesy of AUDI OF AMERICA, INC.
Press --> button to end sequence.
The tester returns to "Select function" mode.

Indicated on display:

Fig 5: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (5 Of 7)

Courtesy of AUDI OF AMERICA, INC.

Press buttons -0- and -6- to select "End output" function 06.

Indicated on display:

Fig 6: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (6 Of 7)

Courtesy of AUDI OF AMERICA, INC.

Press -Q- button to confirm input.

Indicated on display

Fig 7: VAG1551 Scan Tool Display - Code Control Module, Initiating, Telematics (7 Of 7)

Courtesy of AUDI OF AMERICA, INC.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.